AAON RN Series Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 116

AAON RN Series Скачать руководство пользователя страница 77

77

Unit being charged must be at or near full
load conditions before adjusting the charge.

Before Charging

Units equipped with hot gas reheat must be
charged with  the hot gas reheat valves
closed  while the unit is in cooling mode to
get the proper charge.  After charging, unit
should be operated in reheat
(dehumidification) mode to check for
correct operation.

Units equipped with heat pump options
should be charged in heating mode to get the
proper charge. After charging, unit should
be operated in cooling mode to check for
correct charge. Charge may need to be
adjusted for cooling mode. If adjustments
are made in the cooling mode heating mode
must be rerun to verify proper operation.

After adding or removing charge the system
must be allowed to stabilize, typically 10-15
minutes, before making any other
adjustments.

The type of unit and options determine the
ranges for liquid sub-cooling and evaporator
superheat. Refer to the table below when
determining the proper sub-cooling.

Measure the temperature of the liquid line as
it leaves the condenser coil.

Checking Liquid Sub-Cooling

Read the gauge pressure at the liquid line
close to the point where the temperature was
taken. You must use liquid line pressure as it
will vary from discharge pressure due to
condenser coil pressure drop.

Convert the pressure obtained to a saturated
temperature using the appropriate refrigerant
temperature-pressure chart.

Subtract the measured liquid line
temperature from the saturated temperature
to determine the liquid sub-cooling.

Compare calculated sub-cooling to the table
below for the appropriate unit type and
options.

Measure the temperature of the suction line
close to the compressor.

Checking Evaporator Superheat

Read gauge pressure at the suction line close
to the compressor.

Convert the pressure obtained to a saturated
temperature using the appropriate refrigerant
temperature-pressure chart.

Subtract the  saturated temperature  from the
measured suction line temperature  to
determine the evaporator superheat.

Compare calculated superheat to the table
below  for the appropriate unit type and
options.

The Clean Air Act of 1990 bans the
intentional venting of refrigerant
(CFC’s and HCFC’s) as of July 1,
1992. Approved methods of recovery,
recycling or reclaiming must be
followed. Fines and/or incarceration
may be levied for non-compliance.

CAUTION

«
...
75
76
77
78
79
...
»

Содержание RN Series





















































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды