manualshive.com logo in svg

AAON RN Series, Руководство по установке, эксплуатации и обслуживанию

Поделиться
Скачать
AAON RN Series Скачать руководство пользователя страница 12

 

12 

 

 

 
 
1.

 

Startup and service must be performed 
by a Factory Trained Service 
Technician. 
 

2.

 

Use only with type of the gas approved 
for the furnace. Refer to the furnace 
rating plate. 

  
3.

 

The unit is for outdoor use only. See 
General Information section for more 
information. 

 
4.

 

Provide adequate combustion ventilation 
air to the furnace.  If a vent duct 
extension is used, a class III approved 
vent is required. See the Locating Units 
and Gas Heating sections of the 
Installation section of the manual. 

 
5.

 

Always install and operate  furnace 
within the intended temperature rise 
range and duct system external static 
pressure (ESP) as specified on the unit 
nameplate. 

 
6.

 

The supply and return air ducts must  be 
derived from the same space. It is 
recommended ducts be provided with 
access panels to allow inspection for 
duct tightness. When a down flow duct 
is used with electric heat, the exhaust 
duct should be an L shaped duct. 

 
7.

 

Clean furnace, duct and components 
upon completion of the construction 
setup. Verify furnace operating 
conditions including input rate, 
temperature rise and ESP. 

 
8.

 

Every unit has a unique equipment 
nameplate with electrical, operational, 
and unit clearance specifications. 
Always refer to the unit nameplate for 
specific ratings unique to the model you 
have purchased. 

 
9.

 

READ THE ENTIRE INSTALLATION, 
OPERATION AND MAINTENANCE 
MANUAL. OTHER IMPORTANT 
SAFETY PRECAUTIONS ARE 
PROVIDED THROUGHOUT THIS 
MANUAL. 

 
10.

 

Keep this manual and all literature 
safeguarded near or on the unit. 

 
 

 
 

 

COMPRESSOR CYCLING 

 

5 MINUTE MINIMUM OFF TIME 

To prevent motor overheating 
compressors must cycle off for a 
minimum of 5 minutes. 
 

5 MINUTE MINIMUM ON TIME 

To maintain the proper oil level 
compressors must cycle on for a 
minimum of 5 minutes.  
 
The  cycle rate must not exceed 6 
starts per hour. 

 
 

    

 

WARNING

 

 
 

 

WATER FREEZING 

 
Failure of the condenser due to 
freezing will allow water to enter the 
refrigerant circuit and will cause 
extensive damage to the refrigerant 
circuit components.  Any damage to 
the equipment as a result of water 
freezing in the condenser is excluded 
from coverage under AAON 
warranties and the heat exchanger 
manufacturer warranties. 

    

 

WARNING

 

    

 

WARNING

 

Содержание RN Series





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды