manualshive.com logo in svg

AAON RN Series, Руководство по установке, эксплуатации и обслуживанию

Поделиться
Скачать
AAON RN Series Скачать руководство пользователя страница 72

 

72 

Startup 

(See back of the manual for startup form.) 
 

 

 

 

 
During startup, it is necessary to perform 
routine checks on the performance of the 
unit. This includes checking the air flow, air 
filters, condenser water flow, dampers, 
heaters, and refrigerant charge. 
 

Supply Fans 

RN  Series units are equipped with direct 
drive backward curved plenum fan 
assemblies that are selected to deliver the air 
volume specified according to unit size and 
job requirements. This is either done with air 
volume bands in the blower  wheels  or  with 
variable frequency drives. Field airflow 
adjustment may be required at startup. 
 
Air volume bands for the wheels are sized 
according to the unit’s air delivery 
specifications and can also  be ordered from 
the factory for field installation. Wheels 
come standard with a 10% air volume band, 
as a safety factor, in case additional  air 
volume is required from the unit. 
 
 

Air Flow Adjustment 

If reduced air volume is required an air 
volume band  or larger air volume band  can 
be installed within the blower wheel to 
reduce the amount of air delivered by the 
wheel.  
 
If the unit is factory equipped with the air 
volume  band  and  additional air volume  is 
required, the band can be removed from the 
wheel.  
 
Use  fan program in AAON  ECat to 
determine the new band size for the required 
cfm and static pressure. 
 
The following photos of a wheel are 
provided for practical guidelines only in 
order to identify the air band location in the 
wheel. Actual field installation of the air 
band into the wheel will require access into 
and through the blower wheel venture, 
which may require removal of the blower 
motor and wheel. 
 
Air volume bands are made of aluminum, 
sized and equipped with easy bend tabs that 
are to be inserted into pre-punched slots 
provided on the wheel. Once the band has 
been inserted into the slots, it MUST BE 
secured by bending the tabs over from the 
back side of the wheel and also MUST BE 
secured from the inside by connecting the 
ends together with a pop-rivet in the holes 
provided on the ends of the band. 
 
If the band is field installed, a hand held 
pop-rivet tool is recommended for 
connecting the band ends together. Caution 
must be taken to assure that the band is 
tightly installed and no damage, denting or 
alteration to the wheel or blades occurs 
during the installation. 
 
 
 

 
 

 

Electric shock hazard. Shut off all 
electrical power to the unit to avoid 
shock hazard or injury from rotating 
parts. 

    

 

WARNING

 

 
 

 

Improper installation, adjustment, 
alteration, service or maintenance 
can cause property damage, 
personal injury or loss of life. Startup 
and service must be performed  by a 
Factory Trained Service Technician. 

    

 

WARNING

 

Содержание RN Series





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды