manualshive.com logo in svg

A&D AD-4408A, Инструкция по эксплуатации

Поделиться
Скачать
A&D AD-4408A Скачать руководство пользователя страница 22

AD-4408A

 Page 

20 

 

7.2.    Calibration With an Actual Load (

Cal5et

) 

Calibration is performed using a calibration weight 
Before performing calibration for the first time, set the unit, decimal point position, 
minimum division and weighing capacity in the calibration-related function mode. 

NOTE: To avoid drift caused by changes in temperature, warm up the indicator for 

ten minutes or more before performing calibration with an actual load. 

 
Step 1  Press the ON/OFF key to turn the indicator ON (weighing mode) if it is in the 

OFF mode. 
Remove the CAL key cover and press the CAL key.   

   

CalL

 is displayed to indicate that the indicator enters the calibration mode. 

Step 2  Press the ENTER key to display   

Cal5et 

  . The indicator enters the mode of 

calibration with an actual load. To go back to the weighing mode, press the ESC 
key. 

Zero calibration 

Step 3  Press the ENTER key to display   

Cal 0 

 . 

If zero calibration is not to be performed, press the F key and go to step 5. 
To monitor the current weight value, press the CAL key. Press the CAL key 
again to display   

CalL 0

  . 

Step 4  With  nothing  placed on the load cell, wait for the stabilization indicator to turn 

ON and press the ENTER key.   - - - - - -   is displayed for approximately two 
seconds. 
If span calibration is not to be performed, press the ESC key twice to return to 
the weighing mode. 

Span calibration 

Step 5  Press the ENTER key when   

Cal5pn

  is displayed. 

The calibration weight value (the weighing capacity currently set) is displayed 
and the least digit of the value blinks. 

<

 

>

 

∧

 

∨

 

keys: Press to correct the value to the value of the calibration weight 

used. 

CAL key 

: Press to monitor the current value (the gross weight) and   

press again to display the calibration weight value. 

ESC key 

: Press three times to go back to the weighing mode without 

performing span calibration. 

Step 6  Place a calibration weight on the load cell. Wait for the stabilization indicator to 

turn ON and press the ENTER key.   - - - - - -   is displayed for approximately 
two seconds. 

 

Содержание AD-4408A



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды