A.O. Smith GPVL-50 Скачать руководство пользователя страница 38

Страница: 38 / 39

GAS CONTROL LED STATUS CODES

LED Flash Sequence

Control Status

Short

ash

once every four
seconds

IDLE (no call for heat,
no fault conditions)

“Heartbeat”,
alternates bright/dim

Call For Heat
(no fault conditions)

One Flash,
three second pause

Low Flame Signal
(control continues to operate)

Two Flash,
three second pause

Pressure Switch Failed
Closed

Three Flash,
three second pause

Pressure Switch Failed Open

Four Flash,
three second pause

TCO Limit Lockout

Five Flash,
three second pause

Flame Out Of Sequence

Six-One Flash,
three second pause

Soft Lockout
– Retry Limit
- Failed TFI

Six-Two Flash,
three second pause

Soft Lockout
- Recycle Limit
- PS/Limit opened

Six-Three Flash,
three second pause

Soft Lockout
- Recycle Limit
- Flame Lost

Six-Four Flash, three
second pause

Soft Lockout
- Flame out of Sequence
Sensed

Seven Flash,
three second pause

Flammable Vapor Sensor
Lockout

Eight-One Flash,
three second pause

FVS Fault Detected

Eight-Two Flash,
three second pause

Temperature Sensor Fault
Detected

Eight-Three Flash,
three second pause

Electronics Fault Detected

Eight-Four Flash,
three second pause

Valve Fault Detected

IGNITION STATE AND TIMING

IGNITION STATE

TIMING

Pre-purge

5 seconds (NG models)
15 seconds (LP models)

HSI Warmup

10 seconds

Ignition Activation
Period (IAP)

3.5 seconds maximum

Flame Recognition
Period (FRP)

0.5 second

Trial For Ignition

IAP + FRP

Flame Stabilization
Period

Not Applicable

Inter-purge

30 seconds

Flame Failure
Response Time

2 seconds max
(@ 1uA

ame current)

Post-purge

30 seconds

PS Prove Period

2 minutes

PS Fault Delay
(failed open/closed)

2 minutes

Soft Lockout

20 minutes

TCO Limit Lockout

Inde

nite (follow de

ned

procedure to restart)

Flammable Vapor
Sensor Lockout

Inde

nite (follow de

ned

procedure to restart)

Hardware Fault
Lockout

Inde

nite (clear fault to restart

in 15 seconds or less)

Содержание GPVL-50








































Результаты поиска

Содержание GPVL-50

Отзывы:

Похожие инструкции для GPVL-50

Бренды по названию

Популярные бренды

A.O. Smith GPVL-50, Руководство по обслуживанию

Результаты поиска

Содержание GPVL-50

Отзывы:

Похожие инструкции для GPVL-50

Бренды по названию

Популярные бренды