A.O. Smith GPVL-50 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 39

background image

27

FLAMMABLE VAPOR SENSOR

When using a gas

fi

red water heater there is a risk of

fl

ammable vapors entering the combustion chamber, being

ignited by the burner

fl

ame and causing a

fl

ashback. In

order to detect such

fl

ammable vapors before they enter

the combustion chamber, this water heater is equipped
with a

fl

ammable vapor sensor (FVS). It is a chemical-

absorption based sensor that is connected to the gas
control/thermostat (see Figure 31). When exposed to

fl

ammable vapors it will trigger the control to stop the

fl

ow of gas and enter the FVS lockout state. While in the

FVS lockout state the LED on the control will

fl

ash the

gas lockout code. Refer to the “Gas Control Led Status
Codes” section for an explanation of the codes applicable
to the control installed on your water heater. If an FVS
lockout occurs, check around the water heater for sources
of chemical contamination such as

fl

ammable vapors

including gas vapors, solvents, paint and thinners as well
as sources of water and detergents.

Note:

Resetting the heater will reset the FVIR circuit if

all sources of contamination have been removed and the
sensor clears. If all sources of contamination have been
removed and the system will not reset, the sensor will
need to be replaced.

If there is a problem with the wiring of the

fl

ammable vapor

sensor or the

fl

ammable vapor interface the LED will

fl

ash

the failure status code (see “Troubleshooting Guide”).

MOUNTING

BRACKET

FLAMMABLE

VAPOR SENSOR

(PULL TO REMOVE)

COVER*

* ROTATE LEFT (CCW)
TO REMOVE

Figure 31

FV SENSOR

«
...
25
26
27
28
29
...
»

Содержание GPVL-50








































Отзывы:

Нет отзывов

Похожие инструкции для GPVL-50

Бренд: EasyPro Страницы: 8

Бренд: A.O. Smith Страницы: 2

Residential Gas Water Heaters

Бренд: A.O. Smith Страницы: 84

Instant-Flow Micro M-15L/277

Бренд: Chronomite Страницы: 2

Бренд: Rheem Страницы: 48

Бренд: nedis Страницы: 36

Бренд: Glowworm Страницы: 56

Бренд: Singer Страницы: 36

Racor RK15438-01

Бренд: Parker Страницы: 8

PULSAR Shadow Series

Бренд: Pulsafeeder Страницы: 46

Бренд: samhydraulik Страницы: 7

Бренд: Drazice Страницы: 28

Бренд: Salvador Escoda Страницы: 10

Бренд: Samoa Страницы: 4

EMERALD E63-NG1

Бренд: Waterford Страницы: 24

Бренд: Zoeller Страницы: 8

Бренд: Star Progetti Страницы: 41

Бренд: Heatrex Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды