background image

10

InstallatIon

reQuIred aBIlIty

Installation and service of this water heater requires ability equivalent 

to that of a qualified agency (page 2) in the field involved. Plumbing 

and electrical work is required.

General

The  installation  must  conform  with  these  instructions  and  the 

local code authority having jurisdiction and the requirements of the 

power company. In the absence of code requirements, follow NFPA-

70 (current edition). In the absence of local codes, the installation 

must comply with the latest editions of the National Electrical Code, 

NFPA 70 or the Canadian Electrical Code CSA C22.1. The National 

Electrical  Code  may  be  ordered  from:  National  Fire  Protection 

Association, 1 Batterymarch Park, Quincy, MA 02269. The Canadian 

Electrical Code is available from the Canadian Standards Association, 

8501 East Pleasant Valley Road, Cleveland, OH 44131.

Do 

not 

test electrical system before heater is filled with water, follow 

 

the START UP procedure in the OPERATION section of this manual.

The  principal  components  of  the  heater  are  identified  in  the 

Features and Components illustrations on pages 6 and 7.

MIXING VALVE USAGE:

 

Water heaters are intended to produce hot water. Water heated to 

a temperature which will satisfy space heating, clothes washing, 

dish washing, cleaning and other sanitizing needs can scald and 

permanently injure you upon contact. Some people are more likely 

to be permanently injured by hot water than others. These include 

the  elderly,  children,  the  infirm,  or  physically/developmentally 

disabled. If anyone using hot water in your home fits into one of these 

groups or if there is a local code or state law requiring a maximum 

water temperature at the hot water tap, then you must take special 

precautions. In addition to using the lowest possible temperature 

setting  that  satisfies  your  hot  water  needs,  a  means  such  as  a 

MIXInG ValVe

, should be used at the hot water taps used by these 

people or at the water heater.  

MIXInG  ValVes

  for  reducing  point  of  use  temperature  are 

available.  Consult a qualified installer or service agency. Follow all 

manufacturer’s Instructions for installation of these valves. Before 

changing the factory setting on the thermostat, read the “Temperature 

Regulation” section in this manual.

contaMInated water

This  water  heater  shall  not  be  connected  to  any  heating 

system(s)  or  component(s)  used  with  a  non-potable  water 

heating appliance.

Toxic chemicals, such as those used for boiler treatment shall not 

be introduced into this system.

cIrculatInG puMp

Field  installed  circulating  pumps  should  be  of  all  bronze 

construction.

InsulatIon Blankets

Insulation  blankets  are  available  to  the  general  public  for 

external use on electric water heaters but are not necessary with 

this product. The purpose of an insulation blanket is to reduce 

the standby heat loss encountered with storage tank heaters. 

Your water heater meets or exceeds the EPACT and ASHRAE/

IES 90.1 standards with respect to insulation and standby loss 

requirements, making an insulation blanket unnecessary.

Should you choose to apply an insulation blanket to this heater, 

you  should  follow  these  instructions  below.  Failure  to  follow 

these  instructions  can  result  in  fire,  serious  personal  injury, 

or death.

•  Do not cover the temperature and pressure relief (T & P) valve

 

  with an insulation blanket.

•  Do not cover the instruction manual. Keep it on the side of the

 

  water heater or nearby for future reference.

•  Do obtain new warning and instruction labels for placement on

 

  the blanket directly over the existing labels.

teMperature-pressure relIef ValVe

This water heater is provided with a properly rated/sized and 

certified combination temperature - pressure relief valve by the 

Содержание DURA-Power DRE-52













































Отзывы: