A-Maize-Ing Heat NRP620-10 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 87

background image

NRP620-10 OMEPAPV20161017 (ENGLISH) REV 1

Page 32 of 42

Problem

Possible Cause

Possible Corrective Action

Fire goes out

Low fire time too long.

During warm weather when heat is not
needed often, the low fire timer may need
to be adjusted to drive fuel into the burn
pot more often and prevent the fire from
going out.

Furnace
inefficiency

Incorrect timing during low fire
operation.

Adjust OFF time after 24 hours of initial
operation. Refer to “Operation” on page 28
for timing adjustment information.

Poor Combustion

Excessive dirt or fines.



Remove dirt or fines from fuel.



Purchase fuel from a dealer or farmer
that understands the quality of biomass
fuel required for efficient combustion.

Poor Combustion

Fuel moisture too high.



Replace with dry fuel.



Increase combustion air flow gate
opening.



Blend with high BTU rated dry fuel.

Poor Combustion

Flue draft too low.

Furnace requires 0.02 to 0.04 inches of
water column draft on low fire to support
combustion.

Poor Combustion

Combustion air flow too low.



The furnace requires 60 CFM of
combustion air. Increase the opening
of the combustion air intake fan gate.



Install an outside air combustion intake.

Fuel does not feed
smoothly into burn
pot.

High friction in auger drive.

Pour a small amount of powdered graphite
into the auger intake to lubricate the auger
system.

Auger is plugged
or auger motors
do not turn.

Buildup of clinkers in burn pot.

Clean entire burn pot removing all material.

Auger is plugged
or auger motors
do not turn.

Buildup of material in auger
tubes.

Waxy or high oil corn is not recommended
and can cause the auger drive to stop
functioning. Clean out auger system and
repair as necessary.

Auger is plugged
or auger motors
do not turn.

Foreign object(s) in fuel.

Corn cobs, stalks, or other large material
will not pass through the auger system.
They can jam the auger and cause damage.
Clean and repair as necessary.

«
...
33
34
35
36
37
...
»

Содержание NRP620-10
























































































Отзывы:

Нет отзывов

Похожие инструкции для NRP620-10

Бренд: Barnstead International Страницы: 56

Бренд: Empyre Страницы: 30

Бренд: Amana Страницы: 12

CARBOLITE GERO STF 15/450

Бренд: VERDER Страницы: 48

Бренд: SummerAire Страницы: 5

Бренд: Kenmore Страницы: 47

Бренд: Carrier Страницы: 92

Бренд: Johnson Страницы: 24

Бренд: Rapid Страницы: 58

FC085V42A FH085V42A FH110V48AFH110V60A

Бренд: Bard Страницы: 45

Бренд: York Страницы: 4

Бренд: Bryant Страницы: 8

Бренд: Bryant Страницы: 2

EVOLUTION 986TA

Бренд: Bryant Страницы: 14

GAS-FIRED INDUCED-COMBUSTION FURNACES 383KAV

Бренд: Bryant Страницы: 20

CONDENSING GAS FURNACE 350MAV

Бренд: Bryant Страницы: 52

Бренд: Bryant Страницы: 2

368RAN Series A

Бренд: Bryant Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды