3M QS4-15JCN-350-750 Скачать руководство пользователя

Страница: 4 / 16

4 78-8127-8864-0-C

2.5 Carefully bend the cut neutral wires up and away from the cable semi-con. Fold neutral wires over cable jacket,

taking care to keep wire profile low by following the concentric turn in the cable

. Secure the ends of the

neutral wires with one wrap of vinyl tape. Fold one Scotch

Mastic Strip 2230 in half lengthwise and apply one

wrap only at cable jacket edge under the neutral wires

(Figure 3).

Knead mastic around neutral wires.

Insulation

Semi-Con

Neutral Wires

Scotch

Mastic Strip 2230

Scotch

Mastic Strip 2230

Fold mastic strip in half lengthwise

Bend neutral wires

over cable jacket

Figure 3

2.6 Apply an additional

single wrap

of Scotch

Mastic Strip 2230 at the edge of the cable jacket and partially

over the neutral wires. Overwrap mastic with vinyl tape, taking care not to extend tape along neutral wires

(Figure 4).

Scotch

Mastic Strips 2230

Overwrap with vinyl tape

Cable Jacket

1 Wrap of Vinyl Tape

Figure 4

Содержание QS4-15JCN-350-750

















Результаты поиска

Содержание QS4-15JCN-350-750

Отзывы:

Похожие инструкции для QS4-15JCN-350-750

Бренды по названию

Популярные бренды

3M QS4-15JCN-350-750, Инструкция по эксплуатации

Результаты поиска

Содержание QS4-15JCN-350-750

Отзывы:

Похожие инструкции для QS4-15JCN-350-750

Бренды по названию

Популярные бренды