3M QS4-15JCN-350-750 страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 16

background image

3M, and Scotch are trademarks of 3M Company.
All other trademarks are property of their respective owners.

Important Notice

All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable,
but the accuracy or completeness is not guaranteed.

Before using this product, you must evaluate it and determine if it is suitable for

your intended application.

You assume all risks and liability associated with such use.

Any statements related to the product which are not

contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless
expressly agreed upon, in writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability.

This product will be free from defects in material and manufacture at the time of purchase.

3M MAKES NO OTHER WARRANTIES

INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the
3M product or refund the purchase price of the 3M product.

Except where prohibited by law, 3M will not be liable for any indirect,

special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

3

Electrical Markets Division

6801 River Place Blvd.

Austin, TX 78726-9000

800-245-3573

Fax 800-245-0329

www.3M.com/electrical

Please Recycle. Printed in USA.

© 3M 2014. All Rights Reserved.

78-8127-8864-0-C

«
...
14
15
16

Содержание QS4-15JCN-350-750

















Отзывы:

Нет отзывов

Похожие инструкции для QS4-15JCN-350-750

Бренд: Yokota Страницы: 8

Бренд: Mallory Страницы: 8

Бренд: Omer Страницы: 26

Бренд: VacuMaid Страницы: 16

Бренд: Schneider Airsystems Страницы: 20

Бренд: Work Men Страницы: 48

Бренд: Parkside Страницы: 96

Бренд: Neilsen Страницы: 16

Бренд: Westfalia Страницы: 46

Бренд: Magnetic Instrumentation Страницы: 27

Бренд: Yost Vises Страницы: 5

Бренд: MAC TOOLS Страницы: 32

Бренд: Swivelpole Страницы: 2

Бренд: Ferm Страницы: 16

Бренд: Huck Страницы: 26

Бренд: TE Страницы: 6

Бренд: Danco Страницы: 6

Бренд: Facom Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды