3DHISTECH Ltd. Pannoramic SCAN II 2.0 Скачать руководство пользователя страница 106

Страница: 106 / 142

Pannoramic SCAN II 2.0 User’s Guide

5 Scanning modes and settings

◦

Brightfield ICC Profile

Select an applicable preset color profile to be used for Brightfield scanning from the drop-

down menu. Settings according to the profile has effect on the color set, color
temperature, and gamma value of the scanned image.

Preset profiles

are the following:

▪

Calibrated Linear

: Color scheme is defined by calibration (Gamma value is not

included)

▪

sRGB standard

: Color scheme is defined by calibration (standard Gamma value -2.2-

is applied)

▪

sRGB standard Microscope Like

: Color scheme is defined by calibration (standard

Gamma value / White Point: D50)

▪

Legacy

: a Color scheme calibrated for the previous software version is applied

▪

Custom

: parameters are freely customizable as follows:

◦

Color Scheme

▪

Calibrated

: Scheme is defined by the color calibration slide

▪

Legacy

: a Color scheme calibrated for the previous software version is applied

▪

Raw

: the color information of the recorded raw image is applied

◦

White Point

▪

D65

: color temperature according to a standard illuminant D65 white point value is

applied (6500K / daylight)

▪

D50

: color temperature according to a standard illuminant D50 white point value is

applied (5000K / horizontal daylight)

◦

Gamma

▪

Standard

: a value of 2.2 is used

▪

Medium

: a value of 1.8 is used

▪

Off

: a value of 1.0 is used

Note:

If Lumencor SPECTRA 6 is configured as illumination unit, the

corresponding

Enable Lumencor hardware trigger

option is displayed

on the

Filter settings

form.

June 4, 2018 - Rev. 2

3DHISTECH Ltd.

106(142)

For research and education uses only, not for use in diagnostic procedures.

Содержание Pannoramic SCAN II 2.0















































































































































Результаты поиска

Содержание Pannoramic SCAN II 2.0

Отзывы:

Бренды по названию

Популярные бренды

3DHISTECH Ltd. Pannoramic SCAN II 2.0, Руководство пользователя

Результаты поиска

Содержание Pannoramic SCAN II 2.0

Отзывы:

Бренды по названию

Популярные бренды