3DHISTECH Ltd. Pannoramic SCAN II 2.0 Скачать руководство пользователя | Manualshive

Страница: 10 / 142

background image

Pannoramic SCAN II 2.0 User’s Guide

Notes Regarding Operational Safety

Warning!

Check that your local line voltage is compatible with Pannoramic SCAN II
specifications before you turn power on.

Disconnect plug!

Remember to unplug the power cord before you open the Pannoramic SCAN II
main unit for maintenance.

Warning!

Only connect external devices to the instrument which are approved to avoid
the risk of electrical shock.

Warning!

Pannoramic SCAN II does not include any special facilities to protect from
samples with an etching, potentially infectious, toxic, radioactive or other
health-damaging effect. You are under obligation to comply with all currently
binding legislation, notably, national accident prevention rules when handling
samples of this kind.

Caution!

Dirt or dust may adversely impact the operating capability of the Pannoramic
SCAN II. For this reason, measures must be taken to eliminate such influences to
a maximum possible degree. During periods of non-use, the Pannoramic SCAN II
must be protected with a dust cover. Check that power is turned off before you
put the cover on.

Caution!

Do not position the equipment so that it is difficult to operate and to disconnect
the device if necessary.

Crush hazard!

There is crush hazard in the movement area of the slide insert during operation.
Please note that the digitizing process has to be interrupted and the insert
moved via software to the output position before removing the insert.

Warning!

A defective Pannoramic SCAN II is not classified as domestic waste. It must be
properly disposed in accordance with currently valid legal requirements.

Warning!

The Pannoramic SCAN II may not be operated by other than properly instructed
persons. Operating personnel must be fully aware of the potential dangers
which a particular field of application involves. The Pannoramic SCAN II is a
precision instrument which may suffer a significant reduction in operational
functions or even physical destruction following intervention performed in any
nonconforming manner.

Warning!

If a Lumencor SOLA SM II illumination unit is used, the corresponding warnings
included in the manufacturer’s operating manual have to be observed.

June 4, 2018 - Rev. 2

3DHISTECH Ltd.

10(142)

For research and education uses only, not for use in diagnostic procedures.

«
...
8
9
10
11
12
...
»

Содержание Pannoramic SCAN II 2.0















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Pannoramic SCAN II 2.0

Бренд: VALOI Страницы: 56

Бренд: Pandigital Страницы: 2

126KPK Super 8 Slides & Negatives Scanner

Бренд: Jumbl Страницы: 1

Бренд: RIOTEC Страницы: 3

Бренд: Exar Страницы: 20

Бренд: Panasonic Страницы: 396

Land LSP Ex System

Бренд: Ametek Страницы: 48

Бренд: Ametek Страницы: 62

LANDSCAN LSP-HD

Бренд: Ametek Страницы: 72

Бренд: Brookstone Страницы: 24

Бренд: Medion Страницы: 89

IDM-Z2-160-D-1D-J2-SU-N-N0

Бренд: Pepperl+Fuchs Страницы: 27

IDM161-M-1D-J1-BT-N-N0

Бренд: Pepperl+Fuchs Страницы: 30

Бренд: Avision Страницы: 84

NETDELIVER @V5100

Бренд: Avision Страницы: 172

Бренд: Radio Shack Страницы: 32

Бренд: Radio Shack Страницы: 56

Бренд: Regency Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды