2N Helios IP Vario Скачать руководство пользователя страница 69

Страница: 69 / 97

2N TELEKOMUNIKACE a.s., www.2n.cz

69/97

Induction Loop

(Part No. 9159050 – Induction loop amplifier for 2N Helios

intercom, Part No. 9159054 – Induction loop amplifier without Helios accessory, Part

No. 9159051 – External induction loop for wall mounting, Part No. 9159052 - 12 V DC

power adapter) is part of sound system installations for hearing impaired persons that

are equipped with a special hearing aid capable of receiving reproduced sound via a

magnetic field receiver. The system is defined by the IEC 60118-4 standard.

Installation:

The induction loop amplifier can be wall mounted with the use of an internal induction

loop where a signal covering is requested. Outdoor use is possible thanks to the IP65

covering. A four-wire cable of the length of one meter is mounted to the supplied

product for easier connection to the intercom. In the cable are two wires for 12 V DC

supply and two wires for signal input, the wires are connected into interconnection

connector. If you shorten the cable, follow the colour marking.

Before wall mounting run the cable through the hole that you have prepared. Then

mark two mounting holes on the wall, through the amplifier front. Remove the

amplifier and drill the mounting holes. Use the plugs and screws included in the

delivery. Use a drill of the diameter of 6 mm. After fastening, cover the screws with

the blanks supplied.

Use the supplied connectors to connect the amplifier to the intercom and power

supply. The A connector is connected to the amplifier four-wire cable. Insert a special

intercom-connecting cable supplied with the amplifier and 12 V power supply outlets

to the B connector. Connect the special cable to the intercom and connect the power

supply to the mains. You can place the mated A and B connectors into the 2N Helios

cover. The connectors help you connect stripped cables. Open the connector by

pushing a thin screwdriver onto the white spots at its front and close the connector by

sliding the movable part through a side gap.

Finally, test the amplifier function using a suitable receiver for hearing impaired

persons or magnetic field communication tester. No other settings are required.

Specifications:

Supply voltage: 8 – 18VDC

Supply current at 12 V supply:

1 Ω load, full power output; 1.4 A, sine wave signal; 1 A, pink noise signal

Содержание Helios IP Vario


































































































Результаты поиска

Содержание Helios IP Vario

Отзывы:

Бренды по названию

Популярные бренды

2N Helios IP Vario, Руководство по установке

Результаты поиска

Содержание Helios IP Vario

Отзывы:

Бренды по названию

Популярные бренды