![background image](http://html.mh-extra.com/html/sealey/ak2951/ak2951_instructions_1227020001.webp)
The AK2951 torch is portable and lightweight, suitable for heating and soldering. Powered by butane gas (lighter fuel), the torch has slide switch
ignition and automatic flame selection for quick and clean operation.
AK2951 Set comprises: Torch, Hot Air Nozzle, Soldering Tip, Safety Cap.
Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly
maintained, give years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
BUTANE SOLDERING/HEATING TOOL SET
Model:
AK2951
1.
SAFETY INSTRUCTIONS
3.
OPERATING INSTRUCTIONS
AK2951 - 2 - 190503
p
WARNING!
Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using the torch.
3
Familiarise yourself with the applications, limitations and potential hazards of the tool.
3
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
8
DO NOT repair the torch yourself, use an authorised service agent.
p
p
WARNING!
Use and handle the butane gas (lighter fuel) in accordance with any instructions supplied with the fuel.
3
Butane gas is highly flammable, so keep an appropriate fire extinguisher at hand.
3
Ensure that there are no flammable or combustible materials near the work area.
3
Keep the work area clean and uncluttered and ensure that there is adequate ventilation and lighting.
3
Keep children and unauthorised persons away from the work area.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
3
Point the torch away from yourself and others when igniting flame.
3
Keep hands and body clear of the torch head when operating as it becomes very hot.
3
Secure unstable workpiece with a clamp, vice or other adequate holding device.
3
Always use the integral stand when the torch is not in use.
8
DO NOT
get the torch wet.
8
DO NOT
use torch where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning rags etc.
8
DO NOT
use the torch for any purpose other than that for which it is designed.
8
DO NOT
use accessories other than those supplied with, or manufactured specifically for use with, the torch.
p
p
WARNING! DO NOT
touch the torch head during, or immediately after, use. Allow the torch to cool naturally before handling.
8
DO NOT
cool the torch in water.
8
DO NOT
point the torch at yourself, others, or animals.
8
DO NOT
operate the torch when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
allow untrained persons to operate the torch.
8
DO NOT
operate the torch if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT
touch the workpiece close to the heated area as it will be very hot. Allow to cool.
8
DO NOT
leave the torch after use, until it has cooled.
3
When work is complete, allow the torch to cool. Clean the torch and accessories and store in a safe, dry childproof location.
8
DO NOT
store in direct sunlight or where the temperature could exceed 104
O
F/40
O
C
p
p
WARNING!
Failure to use the torch correctly may result in fire, damage and/or personal injury.
s
s
DANGER! The flame is invisible in sunlight - be extremely cautious.
p
p
WARNING! Ensure you have read and understood the safety instructions in Section 1 before using the torch.
Note:
The torch is supplied without butane gas. Before use it must be fuelled as follows:
3.1.
TO FUEL THE TORCH
3.1.1.
Use only high quality butane gas (lighter fuel) to fill the torch.
3.1.2.
Ensure the On/Off switch is in the Off position. See fig. 1, On/Off Safety Switch.
3.1.3.
Follow the instructions on the butane fuel can.
3.1.4.
Apply the can filler tip to the torch base filler valve (figs. 1 & 2). Use a pumping action for best filling results.
3.1.5.
Once full, allow gas in the torch to stand and stabilise for a few minutes before use.
fig. 1
fig. 2
2.
INTRODUCTION