![background image](http://html.mh-extra.com/html/kenwood/sk940-series/sk940-series_user-manual_190776001.webp)
needs time to reset.
●
If you experience problems
with your kettle switching
on and off during use or
switching off before boiling,
check that the flat element
is free from scale - see
“descaling”. If descaling
does not solve the problem
contact Kenwood customer
care.
●
Your kettle is fitted with a scale
filter to hold back limescale
particles.
●
If you find drops of water under
your kettle, don’t worry - it is just
condensation.
boil-dry protection
●
If you switch on with too little
water, your kettle will cut out
automatically. Switch off and let it
cool down before re-filling.
When it has cooled down, the
switch will reset itself.
care and cleaning
Before cleaning, unplug your kettle
and let it cool down.
the outside and powerbase
●
Wipe with a damp cloth, then dry.
Do not use abrasives - they will
scratch the metal and plastic
surfaces.
the inside
●
Wipe with bicarbonate of soda on
a damp cloth. Rinse thoroughly.
●
Even though your kettle comes
with a scale filter, you still need to
clean the inside (and the filter)
regularly.
the scale filter
1 Open the lid.
2 Slide the filter out
.
3
either
rinse under the tap or use
a soft brush.
or
when descaling your kettle,
drop the filter in too. Rinse
thoroughly.
4 Slide the filter back in to refit.
descaling
●
Regular descaling of the flat
element will improve the
performance of your kettle. If the
kettle is not descaled regularly the
build up of limescale may result in
the following:
●
problems may be experienced
with the kettle switching on and
off during use or switching off
before boiling.
●
the kettle may take longer to
boil.
●
the flat element may be
damaged.
Please note: not descaling your kettle
may invalidate your guarantee.
●
When limescale starts to build up
on the heating element, buy a
suitable descaler and descale your
kettle. After descaling, boil with
fresh water several times and
discard. Clean any descaler off the
kettle - it can damage the parts.
●
Some regions of the country have
chalky water. This makes boiled
water look cloudy and leaves a
deposit on the side of the kettle.
This is normal but can be removed
with regular cleaning.
●
Alternatively, to reduce limescale
build up, use filtered water to fill
your kettle.
●
A range of Kenwood jug water
filters are available.
Call Kenwood customer care on
023 92392333
.
safety
●
Avoid contact with steam coming
out of the spout area when
pouring and out of the lid when
refilling.
●
Beware: the metal body of the
kettle will get hot during operation.
●
Keep small children away from the
kettle and never let the cord hang
down over the worktop edge - a
child could grab it and pull the
kettle down.
●
If you do not need so much cord,
shorten it by wrapping any excess
cord around the underside of the
powerbase
.
●
Always unplug your kettle
when not in use.
●
Never overfill - boiling water may
splash out.
●
Never put the kettle, powerbase,
cord or plug in liquid.
●
Do not use if there is
any
damage
to the kettle, powerbase, cord or
plug. Get it checked or repaired:
see ‘service’.
●
This kettle is not intended for use
by young children or infirm persons
without supervision.
●
Young children should be
supervised to ensure they do not
play with the appliance.
●
Caution:
Do not operate the
kettle on an inclined surface.
●
Only use the powerbase supplied
and keep it clean and dry.
●
Make sure the lid is secure before
switching the kettle on.
●
Warning:
Do not remove the lid
while the water is boiling.
●
Make sure the kettle is switched
off before lifting and removed from
the base before filling or pouring.
●
Never put the kettle near or on
cooker hot plates or gas burners.
●
This kettle is for boiling water and
domestic use only.
●
Failure to observe these cautions
may result in damage to the kettle.
before plugging in
●
Make sure your electricity supply is
the same as the one shown on the
underside of your kettle.
important - UK only
●
The wires in the cord are coloured
as follows:
Green and Yellow = Earth, Blue =
Neutral, Brown = Live.
●
This kettle complies with European
Economic Community Directive
89/336/EEC.
before using for the first
time
●
Remove all packaging and any
labels.
●
Fill to ‘MAX’, boil, then pour the
water away. Repeat 2 to 3 times.
know your Kenwood
stainless steel kettle
scale filter
on/off switch with neon
water level window
360˚ powerbase
cord wrap
to use your stainless
steel kettle
1 Fill the kettle through either the
spout or lid. The water level must
be between 'Max' and 200ml
(1 cup).
●
Be economical: do not boil more
water than you need.
●
To improve the quality of your
drinks always use fresh water.
●
Empty the kettle after each use.
2 Check the lid is closed.
3 Plug in and switch on. The neon
will come on.
4 Your kettle will boil and switch off
automatically. To re-boil, wait a
few seconds - the on/off switch
min
m
ax
KE
NW
OO
D
4
6
8