background image

1

GE SmartWater

™  

INSTALLATION INSTRUCTIONS

GE Model GXITQ and GXITQR Filters

Part No. 215C1001P014 

(8-99 JR) 

Pub. No. 49-50027-1

For Use and Care questions call: GE Answer Center® 800.626.2000

GENERAL ELECTRIC COMPANY, Appliance Park, Louisville, KY 40225

Do not use where water is microbiologically

unsafe or with water of unknown quality

without adequate disinfection before or

after the filter.
Small parts remaining after the installation

could be a choke hazard. Discard safely.

SPECIFICATIONS

INSTALLATION PRECAUTIONS

Protect from freezing. Drain filter when room temperature drops below 32°F. (0°C.).

Use the in-line water filtering system on a potable, safe-to-drink, home COLD water supply only. The filter 

will not make unsafe water safe to drink. Do NOT use on HOT water (100°F. max.).

Do not install on line pressure above 125 psi (862 kPa), or below 25 psi (172 kPa).

All of the refrigerator installation requirements must be met when installing the filter. 

Do not use wicking or pipe dope sealer for fitting connections into head of filter. Teflon® tape is

recommended and included. Teflon is a registered trademark of DuPont. 

Do not install in direct sunlight.

Installation must comply with existing state or local plumbing codes.

REQUIRED TOOLS FOR INSTALLATION

a tube cutter

• 

7/16

″, 

1/2

″ 

and 9/16

″ 

wrenches

• 

a knife

• 

a bucket or pan

CAUTION:

Using pliers or vise grips 

WILL

damage the fittings.

OPTIONAL TOOLS FOR INSTALLATION

a file

sandpaper

Your new GE icemaker water filter comes complete with all the necessary hardware for installation. 

Each filter gives you up to six months of great-tasting water. 

Filter should be changed after 6 months of use. 

Service Service 

Max. 

Models Flow rate

Life

Pressure 

Temp.

GXITQ

0.5 gpm 2000 gal. or 6 months 25–125 psi

100° F.

GXITQR

(1.9 lpm)

(7571 liters)

(172–862 kPa) (38° C.)

If slow water or hollow ice occurs, replace filter.

System tested and certified by NSF

international against ANSI/NSF 

Std. 42 for the reduction of chlorine 

(Class 1), and taste and odor.

WARNING

Summary of Contents for SmartWater GXITQ

Page 1: ...ation requirements must be met when installing the filter Do not use wicking or pipe dope sealer for fitting connections into head of filter Teflon tape is recommended and included Teflon is a registered trademark of DuPont Do not install in direct sunlight Installation must comply with existing state or local plumbing codes REQUIRED TOOLS FOR INSTALLATION a tube cutter 7 16 1 2 and 9 16 wrenches ...

Page 2: ...e water supply line and inspect for leaks If a leak occurs tighten nuts or fittings until the leak stops 11 Write the date on the filter and also mark your calendar to replace with another filter after six months PROCEDURE FOR REPLACING THE FILTER 1 Get a bucket and a towel 2 Disconnect the old filter at its inlet first and then its outlet Water source will shut off automatically but some water ma...

Page 3: ...n líneas de agua cuya presión sobrepase las 125 psi 862 kPa o esté por debajo de las 25 psi 172 kPa Es necesario cumplir con todos los requisitos de instalación del refrigerador al instalar el filtro No utilice mecha de soldadura o sellador de tuberías para ajustar la conexión de los accesorios en el cabezal del filtro Para el efecto se incluye y se recomienda la cinta Teflon Teflon es una marca r...

Page 4: ...agua y compruebe que no haya fugas Si se presentara alguna fuga apriete las tuercas o los acopladores hasta que cesen las fugas 11 Escriba la fecha en el filtro y también anótela en su calendario para recordar que debe reemplazar el filtro después de seis meses PROCEDIMIENTO PARA REEMPLAZAR EL FILTRO 1 Consiga una cubeta y una toalla 2 Desconecte el filtro viejo empezando por el extremo de entrada...

Reviews: