Overlap Apex Shed
7' x 5'
Important :
Assembly of this
shed requires a
minimum of two
adults.
Issue 0215
B
OPA7PE
PLAIN END
OPA5WS
WINDOW SIDE
143612358
ROOF SHEET
QTY 2
D
E
N
F
A
OPA75 PARTS LIST
BRDFL57
FLOOR
DDRPT
DOOR
QTY 2
OPA7DDE
DOOR END
44161570PT
1570mm C/STRIP QTY 4
H
M
J
45281630PT
1630mm BATTEN QTY 1
G
Place the corner strips so that they cover the joins
between the panels. Fix each in place using 3 x 30mm
screws
A
2
1
1
C
OPA5PS
PLAIN SIDE
4
F
59121273PAII62PT
1273mm BARGE BOARD QTY 4
K
PCWIN1
GLAZING
QTY 1
H
Top View
B
C
A
Must Pre drill for
each screw used.
37281436PT
1436mm BATTEN QTY 2
O
L
FELT QTY 1
FELT78BL
A
Place the panels on top of the floor. Make sure that all the panels are tight and
flush before fixing them to each other using 3x50mm screws.
Make sure that the panels are sitting flush before fixing them to the floor using
50mm screws making sure that all of the screws are positioned so that they
locate into the bearers underneath.
3x50mm screws for the end panels.
2x50mm screws for the side panels.
Fixing Pack (OPA75DDFP)
This fixing pack is used for several products.
There may be additional fixings.
Not to Scale
Flush Hinge
Qty 4
50mm Screw Qty 22
30mm Nail Qty 56
25mm Screw Qty 39
Hasp & Staple
30mm Screw Qty 22
I
FIN20010512PTR
Finial
QTY 2
37281352PT
1352mm BATTEN QTY 4
E
A
B
A
C
A
D
J
L
D
Z’ bracket Qty 8
Ridge Plate
Turn Button
Qty 2
IMPORTANT, RETAIN FOR FUTURE REFERENCE; READ
CAREFULLY
This buildings is pressure treated to ensure longevity of all
timber components and to protect against rot. This may leave
a colour difference on some parts that will even out as the
moisture content stabilises. This will not need additional
treatment.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Due to the nature of the material the doors may need some
trimming for a neater fit.
- Please keep all plastic bags and small parts away from
children
- The roof of this building is not a load bearing structure.
- This product must be built on a solid level base.
Technical Help line:
0333 7777 089
8.30 am and 5.00
pm Monday to Friday.
Please check all parts prior to assembly
Assembly of damaged parts may be deemed to be
acceptance and this may affect the remedies you are entitled
to. If the product is not constructed in accordance with the
instructions, or is altered in anyway (e.g. painted), the
manufacturer cannot be held liable for any resulting damage.
REQUIRED TOOLS :
(NOT SUPPLIED)
POZI DRIVE
SCREWDRIVER
TAPE MEASURE
HAMMER
SHARP KNIFE
FLAT HEAD
SCREWDRIVER
SCISSORS
84996
675mm PLASTIC STRIP QTY 3
A
40mm Screw Qty 12
10mm Felt tacks Qty 100
25mm Security Screws
Screws Qty 7
3
J
Place the 1630mm batten against the inside of the door so that it is tight against the battens on the reverse and
leaves a small gap at the top and bottom. Fix the batten in place with 4 x 30mm Nails hammering through the
door into the batten.
(make sure the batten is supported from the other side when fixing)
Fix a turn button to the top and bottom of the batten so that the door will be held closed when fixed. Use a 30mm
screw for each turn button.
Place the hinge against the inside of the door frame and position the large section of the hinge so
that it is flush with the inside of the framing as shown and fix with 25mm screws.
Open the hinge and fix the smaller section to the door framing. Again make sure that the hinge is
flush and that the holes are positioned so that the 25mm screws locate correctly into the batten.
