CONFIDENTIAL
THIS DOCUMENT IS THE PROPRIETARY PROPERTY OF FC LIGHTING, INC. ANY UNAUTHORIZED TRANSFER, USE OR REPRODUCTION IS STRICTLY PROHIBITED.
© FC LIGHTING, INC.
FCSL2000 Series
- INSTALLATION INSTRUCTIONS
CAUTION: BEFORE CONNECTING THE FIXTURE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
DETAILED ILLUSTRATION
STUD WALL INSTALLATION
corporate
t
800.900.1730
f
630.889.8106
3609 Swenson Ave.
St. Charles, IL 60174
2458893
GENERAL
:
1. Before starting the installation, make sure all electricity has
been turned off and electrical breaker has been locked out
and tagged out.
2. To ensure the success of the installation, be sure to read
these instructions and review the diagrams thoroughly before
beginning.
3. All electrical connections must be in accordance with local
codes, ordinances, or the National Electrical Code.
NOTE
: The important safeguards and instructions appearing in
this manual are not meant to cover all possible conditions and
situations that may occur.
IMPORTANT:
Temporarily remove Splatter Shield and contents
from Back Box housing and set aside.
1. Install Drywall Mounting Brackets onto Back Box using 6-32
screws provided.
Orient Back Box as shown
.
Fig 1
2. Adjust brackets to align front face of backbox flush to face of
finished wall surface. Then fasten brackets to studs.
Fig 2
3. Orient Back Box housing as shown to attach conduit.
Connect conduit to backbox using 3/4” K.O.s.
Fig 3
4. Optional Hanger Bar Brackets can be used to hang the Back
Box between studs or braces to complete installation.
Fig 4
6. Reinstall Splatter Shield and all contents using the (2) 8-32
screws provided.
Fig 5
IMPORTANT
: All wiring connections must be made in
accordance with local electrical codes, ordinances, and the
National Electric Code.
ST
UD
Back Box
Adjustable Back Box
Position In / Out
Drywall
Mounting Brackets
Back Box
Adjustment Slots
6-32 screws
provided
Align to face of
finished wall
Fig 1
Fig 2
Back Box Conduit Entry____
Foam Block Insert to
Retain Back Box Form
Splatter Shield
Wing Nuts
Threaded Rod
SL2000 Series
Universal Back Box
Concrete Pour Form
(by others)
(4) 3/4” Knockouts -
(2) on back and
(1) on each side
Fig 3
Back Box Splatter Shield____
8-32 screws
provided
BACKBOX
STUD
MOUNTING BRACKETS
Figure 2 (stud wall)
MOUNTING BRACKETS
BACKBOX
ADJUSTMENT SLOTS
Figure 1 (stud wall)
Figure 3 (stud wall)
SPLATTER GUARD
SL 2000 series backbox installation in hollow
(stud) wall construction (2” x 4” min.):
1. Install the (2) slotted mounting brackets
provided as shown in Figure 1, using the (4) 6-
32 screws provided.
2. Adjust the brackets (by loosening the
screws) so that the front face of the backbox
will be flush or slightly in front of the finished
wall surface after installation (see Figure 2).
3. Orient fixture housing electrical
connections as directed on inisde label.
Failure to do so will result in faceplate not
installed in the correct oreintation (critical
STEP for SL2003, SL2040, and SL2041 models).
4. Secure the mounting brackets to wood or
metal studs (hardware by others) so that the
front face of the back box will be flush or
slightly in front of the finished wall surface
after installation (see Figure 2).
5. Connect conduit to backbox using 3/4”
NPT fittings. Pull wires into back housing for
electrical connections to be made later.
6. Install splatter guard provided as shown in
Figure 3, using the (2) 8-32 screws provided
securely and finish wall.
7. Before continuing, remove splatter guard
and debris from backbox to allow for proper
fitment.
SL 2000 SERIES
STUD WALL INSTALLATION
FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW
Foam Block Insert to
Retain Back Box Form
Splatter Shield
Wing Nuts
Threaded Rod
SL2000 Series
Universal Back Box
Concrete Pour Form
(by others)
BACKBOX
STUD
MOUNTING BRACKETS
Figure 2 (stud wall)
MOUNTING BRACKETS
BACKBOX
ADJUSTMENT SLOTS
Figure 1 (stud wall)
Figure 3 (stud wall)
SPLATTER GUARD
SL 2000 series backbox installation in hollow
(stud) wall construction (2” x 4” min.):
1. Install the (2) slotted mounting brackets
provided as shown in Figure 1, using the (4) 6-
32 screws provided.
2. Adjust the brackets (by loosening the
screws) so that the front face of the backbox
will be flush or slightly in front of the finished
wall surface after installation (see Figure 2).
3. Orient fixture housing electrical
connections as directed on inisde label.
Failure to do so will result in faceplate not
installed in the correct oreintation (critical
STEP for SL2003, SL2040, and SL2041 models).
4. Secure the mounting brackets to wood or
metal studs (hardware by others) so that the
front face of the back box will be flush or
slightly in front of the finished wall surface
after installation (see Figure 2).
5. Connect conduit to backbox using 3/4”
NPT fittings. Pull wires into back housing for
electrical connections to be made later.
6. Install splatter guard provided as shown in
Figure 3, using the (2) 8-32 screws provided
securely and finish wall.
7. Before continuing, remove splatter guard
and debris from backbox to allow for proper
fitment.
SL 2000 SERIES
STUD WALL INSTALLATION
FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW
Fig 5
Fig 4
Optional - Hanger Bar
(
HB
)
______
26” Max Length
(14.25” Min Length)
Horizontal Adjustment
26” Max Length
Wall Stud
Wall Bracing
Wall Stud
Hanger Bar
Hanger Bar
(14.25” Min Length)
Vertical Adjustment
Drywall Mounting Brackets
included w/ Back Box Kit
