manualshive.com logo in svg

ZyXEL Communications P-660H-T1 v2, User Manual

Share
Download
ZyXEL Communications P-660H-T1 v2 User Manual Download Page 95

 Chapter 6 LAN Setup

P-660H-Tx v2 User’s Guide

95

To change your ZyXEL Device’s IP alias settings, click 

Network

 > 

LAN

 > 

IP Alias

. The 

screen appears as shown.

Figure 49   

LAN IP Alias

The following table describes the labels in this screen.

Table 25   

LAN IP Alias

LABEL

DESCRIPTION

IP Alias 1, 2

Select the check box to configure another LAN network for the ZyXEL Device.

IP Address

Enter the IP address of your ZyXEL Device in dotted decimal notation. 
Alternatively, click the right mouse button to copy and/or paste the IP address.

IP Subnet Mask

Your ZyXEL Device will automatically calculate the subnet mask based on the IP 

address that you assign. Unless you are implementing subnetting, use the subnet 

mask computed by the ZyXEL Device.

RIP Direction

RIP (Routing Information Protocol, RFC 1058 and RFC 1389) allows a router to 

exchange routing information with other routers. The 

RIP Direction

 field controls 

the sending and receiving of RIP packets. Select the RIP direction from 

None/

Both

/

In Only

/

Out Only

. When set to 

Both

 or 

Out Only

, the ZyXEL Device will 

broadcast its routing table periodically. When set to 

Both

 or 

In Only

, it will 

incorporate the RIP information that it receives; when set to 

None

, it will not send 

any RIP packets and will ignore any RIP packets received.

RIP Version

The 

RIP Version

 field controls the format and the broadcasting method of the RIP 

packets that the ZyXEL Device sends (it recognizes both formats when receiving). 

RIP-1

 is universally supported but RIP-2 carries more information. RIP-1 is 

probably adequate for most networks, unless you have an unusual network 

topology. Both 

RIP-2B

 and 

RIP-2M

 sends the routing data in RIP-2 format; the 

difference being that 

RIP-2B

 uses subnet broadcasting while 

RIP-2M

 uses 

multicasting. Multicasting can reduce the load on non-router machines since they 

generally do not listen to the RIP multicast address and so will not receive the RIP 

packets. However, if one router uses multicasting, then all routers on your network 

must use multicasting, also. By default, RIP direction is set to 

Both

 and the 

Version set to 

RIP-1

.

Summary of Contents for P-660H-T1 v2

























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands