Zycoo ZX20 SERIES User Manual Download Page 26

Page: 26 / 69

- 25 -

Item

Explanation

Extension

The number that users call in order to access the

conference room, the default number is "900".

Guest Password

Guest enter the conference room by this code.

Administrator

Password

Administrator enter the conference room by this code.

Conference DialPlan

Use the DialPlan when you invite the other participant.

Play hold music for

first caller

Check this option, Asterisk will play Hold Music to the first

user in a conference, until another user has joined the

same conference.

Enable caller menu

Checking this option allows a user to access the

Conference Bridge menu by pressing the * key on their

dialpad.

Announce callers

Checking this option announces to all Bridge participants,

the joining of any other participants.

Record conference

Recording format is WAV

。

Quiet Mode

If this option was checked, all users entering this

conference will be marked as quiet, and will be in

Summary of Contents for ZX20 SERIES





































































Search results

Summary of Contents for ZX20 SERIES

Reviews:

Related manuals for ZX20 SERIES

Brands by name

Popular brands

Zycoo ZX20 SERIES, User Manual

Search results

Summary of Contents for ZX20 SERIES

Reviews:

Related manuals for ZX20 SERIES

Brands by name

Popular brands