Zycoo ZP302 User Manual Download

Page: 33 / 55

ZP302 User Manual

Enable Via rport

Enable/Disable system to support RFC3581. Via rport is special

way to realize SIP NAT.

Enable PRACK

Enable or disable SIP PRACK function, suggest use the default

config.

Long Contact

Set more parameters in contact field; connection with SEM server

Enable URI Convert

Convert # to %23 when send the URI.

Dial Without Register

Set call out by proxy without registration;

Ban Anonymous Call

Set to ban Anonymous Call;

Forward Type

Select call forward mode, the default is Off



Off

：

Close down calling forward



Busy

：

If the phone is busy, incoming calls will be forwarded

to the appointed phone.



No answer

：

If there is no answer, incoming calls will be

forwarded to the appointed phone.



Always

：

Incoming calls will be forwarded to the appoint

phone directly.

The phone will Prompt the incoming while doing forward.

Forward Phone Number

Appoint your forward phone number.

Server Type

Select the special type of server which is encrypted, or has some

unique requirements or call flows.

DTMF Mode

Select DTMF sending mode, there are three modes:



DTMF_RELAY



DTMF_RFC2833



DTMF_SIP_INFO

Different VoIP Service providers may provide different modes.

RFC Protocol Edition

Select SIP protocol version to adapt for the SIP server which uses

the same version as you select. For example, if the server is

CISCO5300, you need to change to RFC2543, else phone may not

cancel call normally. System uses RFC3261 as default.

Transport Protocol

Set transport protocols, TCP or UDP;

RFC Privacy Edition

Set Anonymous call out safely; Support RFC3323and RFC3325;

Transfer Expire Time

The phone send bye and end the call as soon as hang up.

Enable Conference

Number

Enable/Disable conference

Enable Displayname

Quote

Set to make quotation mark to displayname as the phone sends

out signal, in order to be compatible with server.

Click to Talk

Set click to Talk ( need practical software support).

Signal Encode

Enable/Disable Signal Encrypt.

RTP Encode

Enable/Disable RTP Encrypt.

Enable Session Timer

Set Enable/Disable Session Timer, whether support RFC4028.It

will refresh the SIP sessions.

Answer With Single

Codec

Enable/Disable the function when call is incoming, phone replies

SIP message with just one codec which phone supports.

Auto TCP

Set to use automatically TCP protocol to guarantee usability of

Summary of Contents for ZP302
























































Search results

Summary of Contents for ZP302

Reviews:

Related manuals for ZP302

Brands by name

Popular brands

Zycoo ZP302, User Manual

Search results

Summary of Contents for ZP302

Reviews:

Related manuals for ZP302

Brands by name

Popular brands