background image

Instruction Manual

Operation

AKI 2

11

6. July 2006, muj_1

D

An initialisation process is performed:

• After the initialisation the head automatically returns to the previously selected 

position.

4.5

Initialisation

1 Starting initialisation (11851):

– Z-OFFSET (

1183

)

value is set automatically on zero

– POS DOWN (

1182

)

value is set automatically on zero

– POS UP (1181)

 is not changed

2 If necessary set the cutting depth (POS DOWN (

1182

))

4.6

Park station

(Fig. 7) AKI2 place of deposit

• After the automatic initialisation place the AKI2 on the park station.

Important

The value for AKI OFFSET1 T1 - T4 (

118521

 - 

118524

) is set on -1.2 mm as 

standard practice. If necessary check this value before starting the automatic 
initialisation.

Caution!

Risk of damaging the equipment

If the AKI2 is placed on the table and the automatic initialisation is started, bar or 
head can collide with the AKI2.

• Place the AKI2 before and after the initialisation in the park station.
• Check before the automatic initialisation whether the AKI2 is anchored correctly 

in the positioning aid.

w00022

Summary of Contents for AKI 2













Reviews: