Instruction manual
www.
kraftoo
l.hk
www.
kraftool.hk
Wall chaser
14
15
Check the status of the mains cable regularly. Do
not allow insulation damage, contamination
with aggressive and conductive substances,
excessive pulling and bending loads.
The damaged cable must be replaced
immediately at the service center.
Turn off the product from the mains as soon as
it is finished.
Turn off the product only with switch 7. Do not turn
it off by simply unplugging the cable from
the mains (removing the plug from the outlet).
Maintenance
Periodically clean the product body, cable, and air
vents from dirt and dust.
Replace the graphite brushes of the motor
periodically (as they wear out) in accordance with
the section “periodic maintenance”.
The product does not require any other special
maintenance.
All other work, including repairs, must be carried
out only by qualified service center specialists,
using original ZUBR spare parts.
Make sure that the product is always in good
condition.
In case of suspicious odors, smoke, fire, sparks,
turn off the product, disconnect it from the mains
and contact a specialized service center.
If the product appears to be defective, stop using it
immediately.
Due to the technical complexity of the product, the
limit state criteria cannot be determined by the
user independently. If there is an obvious or
suspected problem, refer to the section
"Troubleshooting". If the problem is not listed or
you are unable to fix it, contact a specialized
service center. The service center issues an
opinion on the limit state of the product or its parts
in the form of a corresponding Act.
Safety
Insctructions
Before
any
Assembly/adjustment
actions, disconnect the product from the mains
and wait for the discs to stop rotating.
Before starting work, inspect and visually
check the product, cable, and cutting discs for
visible mechanical damage.
The product is not intended for wet cutting.
IN
ANY CASE DO NOT
use water to wet the discs
or surfaces.
Do not install any replacement tools on the
product other than diamond discs (including other
types of discs), or those that do not match
the characteristics of this product.
Always use the supplied additional handle when
performing
work.
Operation
without
an
additional handle is
PROHIBITED
.
Before connecting the product to the
network,
MAKE
SURE
hat the switch is in the off
position.
Before cutting concrete, make sure that there
are no hidden wiring or pipes in the cut areas.
When working, the disks get very hot - do
not touch them immediately after they stop and
until they cool down completely.
Do not cover the air intake openings of
the product.
Do not touch the moving parts of the
product (under the covers).
Use only serviceable cutting discs.
IN ANY CASE, DO NOT
use discs with
visible mechanical damage.
After turning off the product, the discs continue to
rotate for a while. Do not put the product down,
wait for the discs to stop completely.
When working in conditions such as dust,
vibration,
or
high
noise
levels,
use
personal protective equipment and limit the total
(per shift) time spent working with the product.
Warranty
obligations
We constantly care about improving the quality of
service to our customers, so if you have any
complaints about the quality and timing of warranty
repairs, please report it to the
3Y6P
support
service
by
cs
@
kraftool.hk
.
This
warranty does not limit the buyer's right to
claims arising from the contract of sale, and
does not limit the legal rights of consumers.
We provide a guarantee for
3Y6P
tools under the
following conditions:
1)
The Warranty is provided in accordance with the
following conditions by free troubleshooting of the
tool during the established warranty period, which
is proved to be caused by defects in material or
workmanship.
2) The Warranty period begins from the date of
purchase of the instrument by the first owner.
3) The warranty Period and conditions depend on
the series and article of the instrument, please
read the warranty terms carefully at the time of
purchase.
Basic warranty
The warranty period is 6 months from the date of
sale.
ATTENTION
4)
The Warranty does not apply to:
a)
Parts subject to working and other types of
natural wear, as well as tool failures caused by
these types of wear. And also on the tool having
full development of a resource, strong external
or internal pollution.
b)
Malfunctions of the tool caused by non-
compliance with the operating Instructions or
occurred as a result of the use of the tool for
other purposes, during use in environmental
conditions beyond those specified in the
operating Instructions, improper production
conditions, due to overload or insufficient,
improper
maintenance
or
care.
The
unconditional signs of overload of the product
include, among others: the appearance of colors
of fatigue, simultaneous failure of the rotor and
stator, deformation or melting of parts and
components of the product, darkening or
charring of the motor wires under the influence
of high temperature.
c)
When using the product in conditions of high
intensity of work and superheavy loads.
d)
On preventive and maintenance of the tool,
for example: lubrication, washing.
e)
Tool Malfunctions due to the use of
accessories, accessories and spare parts that
are not original accessories/parts of
3Y6P
company.
e) Mechanical damage (cracks, chips, etc.) and
damage caused by aggressive media, high
humidity and high temperatures, ingress of
foreign objects into the vents of the tool, as well
as damage caused by improper storage and
corrosion of metal parts.
g) Accessories, wear parts and consumables
that have failed due to normal wear, such as:
drive belts, battery packs, barrels, guide rollers,
protective covers, collars, cartridges, soles, saw
chains, saw tires, sprockets, tires, carbon
brushes, knives, saws, abrasives, drills, drills,
fishing line for the trimmer, etc.
h) A tool in the design of which changes or
additions have been made.
I) A Slight deviation from the declared properties
of the tool, which does not affect its value and
the possibility of using it for its intended purpose.
