Instruction manual
www.
kraftoo
l.hk
www.
kraftool.hk
Wall chaser
10
11
Check for damage to the product and accessories that may have occurred during transportation.
Specifications
Parameter
ZS
H
-P45-2100 PVTK
ZS
H
-P65-2600 PVSTK
Supply voltage, V
~220±10%
~220±10%
Current frequency, Hz
50
50
Maximum power consumption, W
2100
2600
Frequency of idling rotation, rpm
8000
6000
Cutting disc diameter, mm
180
230
Landing disc diameter, mm
22.2
22.2
Wall chasing depth, mm
0–45
20–65
Groove width, mm
4.3–35
4.3– 40
Wall chasing width setting step, mm
4.3
4.3
Soft start
yes
yes
Constant electronics
—
yes
Overload protection
—
yes
Dust protection
yes
yes
Sound power level (K=3 dB), dB
114
115
Sound pressure level (K=3 dB), dB
104
105
RMS vibration acceleration (K=1.5 ), m/s2
3.8
3.8
Safety class according to GOST 12.2.007.0-81
II
II
Product weight, kg
8
10
Package weight, kg
11
14
Assigned service life, years
5
5
Assigned retention period, in
*
years
7
7
Contents of delivery
Wall chaser
1
pc
.
1 pc.
Case
1
pc
.
1 pc.
Imbus key
1
pc
.
1 pc.
Pressure washer
2
pc
s
2
pc
s
Set washer
7
pc
s
8
pc
s
Tightening key
1
pc
.
1 pc.
Additional Handle
1
pc
.
1 pc.
Safety instruction
1
copy
1 copy
Instruction manual
1 copy
1 copy
* designated storage period (the period from the date of manufacture to the sale of the tool to the user)
Purpose
and scope
ZUBR electric wall chaser is intended for cutting of
chases in concrete and brick surfaces.
Please read these operating instructions carefully,
including the section "Safety Instructions" and
Appendix "General Safety Instructions". This is the
only way you can learn how to handle the tool
correctly and avoid mistakes and dangerous
situations.
The product is designed for use in temperate
climates with temperatures ranging from -10 to
+40°C, relative humidity not exceeding 80%, no
direct exposure to rainfall and excessive dust.
The product meets the requirements of the
Technical Regulations of the Customs Union:
■ TR CU 010 / 2011 "On safety of machinery and
equipment";
■ TP CU 004 / 2011 "On safety of low-voltage
equipment";
■ TP CU 020 / 2011 "Electromagnetic
compatibility of technical equipment".
This manual contains the most comprehensive
information and requirements that are necessary
and sufficient for reliable, efficient and safe
operation of the product.
As a result of further development, the
manufacturer reserves the right to make minor
changes to the product which are not reflected in
this manual and which do not affect the efficient
and safe operation of the product.
The product may be used only by persons of
the age of majority; having skills and/or
knowledge of the principles of working and
operating of the product; being in a sober
state; not under the influence of medications
causing sleepiness and / or reduced
concentration; not having diseases causing
similar conditions, as well as other
contraindications for work with such tools.
All repair work shall be carried out only by
qualified specialists of service centers, using
original spare parts of ZUBR.
Preparation for work
Disconnect the product from the mains and
wait for the discs to stop rotating before
performing any assembly/adjustment activities.
Installing the discs (Fig. 1)
To install the disc(s):
■ remove the screws 5 from the protective cover
11
. Remove the cover;
■ by pressing the spindle lock button 10, use the
supplied tightening key to unscrew the pressure
flange
12
;
■ install the disc(s) with the required number of
washers between them. The thickness of the set-
up flange is 4.3 mm.
NOTE!
The first disc can be installed on the lowest
flange or between any two other flanges.
The direction of the disc rotation (indicated on
the disc itself) must coincide with the direction
of the spindle rotation (indicated on the disc
cover).
■ reattach the pressure flange
12
, press the lock
button
10
and tighten the pressure flange FIRMLY
with the tightening key;
Always tighten the pressure flange FIRMLY to
avoid injury or damage to the product.
■ reattach the cover
11
;
■ tighten the cover mounting screws
5
.
If you need to perform only one cut, remove the
extra disc(s) in the order described above.
Installing an additional handle (Fig.2)
Install the additional handle
1
on the required side
and tighten it firmly.
ATTENTION
ATTENTION
ATTENTION
ATTENTION
