Zte ZXV10 W811N User Manual Download Page 7

Page: 7 / 57

Name

Status

Description

Blinking

The device is starting up, upgrading software, or

detecting an error during self-check.

Status

Off

The device works normally.

The device is powered on.

Power

Off

The device is powered off or is faulty.

The device enables the WLAN function normally.

Blinking

The device is transmitting data.

WLAN

Off

The device does not enable the WLAN function or is

faulty.

The device is successfully connected to the

10M/100M/1000M Ethernet port.

Blinking

The device is transmitting data.

Eth

Off

The device fails to connect to the Ethernet port or is

faulty.

2.4

Interface

Interface Description

Description

ZXV10 W811NThe interfaces and buttons are described in the table as below.

Interface Name

Description

Power

Power interface, connected to the original power adapter

accompanying the device

Reset

Reset button; in power-up running status, keep pressing the

button for over 5s, and the current configuration will be reset as

factory-leaving configuration. The system will restart automatically

Ethernet

Ethernet interface, connected to the network port of computer or

other network equipment through the RJ-45 network wire

COM

Console port, connecting the computer and the Console port;

Baud rate is 115200. It supports the user to manage and debug

equipments through the Console mode (not suggested for normal

users)

Product

Product Installation

Installation

3.1

Installation

Installation Requirements

Requirements

Before the device is installed and used, the following requirements must be met:

Summary of Contents for ZXV10 W811N


























































Search results

Summary of Contents for ZXV10 W811N

Reviews:

Related manuals for ZXV10 W811N

Brands by name

Popular brands

Zte ZXV10 W811N, User Manual

Search results

Summary of Contents for ZXV10 W811N

Reviews:

Related manuals for ZXV10 W811N

Brands by name

Popular brands