zortrax Apoller User Manual Download Page 57

Page: 57 / 62

©2019, Zortrax S.A. All rights reserved. All trade names, logos and trademarks mentioned in the following
document are registered trademarks of Zortrax and are subject to legal protection

#012 NTC1_ERROR

Thermistor no. 1 has failed.

Contact Zortrax Support Cen-

ter through the support form:

https://support.zortrax.com/

support-form/

#013 NTC2_ERROR

Thermistor no. 2 has failed.

Contact Zortrax Support Cen-

ter through the support form:

https://support.zortrax.com/

support-form/

#014 NTC3_ERROR

Thermistor no. 3 has failed.

Contact Zortrax Support Cen-

ter through the support form:

https://support.zortrax.com/

support-form/

#015 NTC4_ERROR

Thermistor no. 4 has failed.

Contact Zortrax Support Cen-

ter through the support form:

https://support.zortrax.com/

support-form/

#016 NTC5_ERROR

Thermistor no. 5 has failed.

Contact Zortrax Support Cen-

ter through the support form:

https://support.zortrax.com/

support-form/

#017 NTC6_ERROR

Thermistor no. 6 has failed.

Contact Zortrax Support Cen-

ter through the support form:

https://support.zortrax.com/

support-form/

#019 OVERHEAT_ERROR

Chamber has reached critical

temperature. Heating control

board has failed.

Contact Zortrax Support Cen-

ter through the support form:

https://support.zortrax.com/

support-form/

#020 HC_DISCONNECT

Heating control board has fa-

iled.

Contact Zortrax Support Cen-

ter through the support form:

https://support.zortrax.com/

support-form/

Summary of Contents for Apoller






























































Search results

Summary of Contents for Apoller

Reviews:

Related manuals for Apoller

Brands by name

Popular brands

zortrax Apoller, User Manual

Search results

Summary of Contents for Apoller

Reviews:

Related manuals for Apoller

Brands by name

Popular brands