ZONGSHEN ZS250GY-3 Service Manual Download

Page: 42 / 76

LIS

Table4-10

Maintenance of Wheel

3 The cause,trouble description and repair method of wheel

Component

Description

Cause

Trouble description of

component

Trouble description of motor

cycle

Repair method

front wheel

Front wheel is

distorted.

Front wheel is

distorted.

Motorcycle runs towards one

side and turning handlebar

shakes during running.

Replace front

wheel.

The bearing hole

of wheel hub is

worn.

The match of bearing

hole of wheel hub and

bearing is too loose.

Motorcycle runs towards one

side and turning handlebar

shakes during running.

Bearing is worn

or damaged.

The axial and radial

clearance of inner and

outer bearing is too

big or its rotation is not

flexible.

Motorcycle runs towards one

side and turning handlebar

shakes during running.

Replace bearing.

front tire

Tire is worn.

It is easy to slide during

running and it is hard to

avoid side sliding.

Replace outer tire.

gear box of

speedometer

Gear is damaged.

Speedometer finger cannot

swing.

Replace the

gear box of

speedometer.

The transmission

ring of gear wheel

is damaged.

Speedometer finger cannot

swing.

Replace the gear

box of speedometer.

rear wheel

Rear wheel is

distorted.

Rear aluminium wheel

is distorted.

Motorcycle runs towards

one side and rear wheel

shakes during running.

Replace bearing.

Rear wheel is

damaged.
The bearing hole

of wheel hub is

worn.

The match of bearing

hole of wheel hub and

bearing is too loose.

Bearing is worn

or damaged.

The axial and radial

clearance of inner and

outer bearing is too

big or its rotation is not

flexible.

rear tire

Rear tire is worn.

It is easy to slide during

running and it is hard to

avoid side sliding.

Replace outer tire.

Summary of Contents for ZS250GY-3













































































Search results

Summary of Contents for ZS250GY-3

Reviews:

Related manuals for ZS250GY-3

Brands by name

Popular brands

ZONGSHEN ZS250GY-3, Service Manual

Search results

Summary of Contents for ZS250GY-3

Reviews:

Related manuals for ZS250GY-3

Brands by name

Popular brands