ZONGSHEN ZS250GY-3 Service Manual Download

Page: 22 / 76

LIS

4 Disassembly and Maintenance of Exhaust
System

[1]Dismantle the locknut of exhaust pipe of muffler
and suspension bolt of muffler.Check whether the
suspension bracket is broken.Re-joint it if broken.

[2]Remove muffler and check whether the muffler
is broken or damaged.Re-joint or replace it when
broken or damaged.

[3]Remove the seal gasket of muffler and check
whether the gasket is damaged.Replace it if
damaged.

When the suspension bracket of muffler is

broken,replace or re-joint it.

The seal gasket must be replaced ever y

disassembly of muffler.

CAUTION

[4]Check whether there is carbon deposit in the
muffler pipe.Clean it.

Check Whether muffler is rusty or broken.

Replace or maintain it if necessary.

CAUTION

Locknut

Seal gasket

Muffler

pipe

muffler

Summary of Contents for ZS250GY-3













































































Search results

Summary of Contents for ZS250GY-3

Reviews:

Related manuals for ZS250GY-3

Brands by name

Popular brands

ZONGSHEN ZS250GY-3, Service Manual

Search results

Summary of Contents for ZS250GY-3

Reviews:

Related manuals for ZS250GY-3

Brands by name

Popular brands