ZONGSHEN ZS250GY-3 Service Manual Download

Page: 56 / 76

LIS

[2]Remove the flasher socket of signal system and
measure the flasher with multimeter.Check whether
it has short circuit.Replace it if short circuit.

[3]Check whether starting relay is in good working
condition.Replace it with the same type if it is not
in good working condition.

[4]Dismantle the switches of left and right controls.
Check whether they are damaged or have short
circuit.Repair or replace them if have problems.

Check whether front/rear brake switches are in

good working condition.Readjust or replace them
if they are not in good working condition.

If front/rear brake light do not shine when

braking,then there is no electric power to start.

[5]Remove fuse tube and check whether it melts.
Replace it with the same type.

Fuse tube type

：

12V/20A

Replace fuse tube with the same type when it

is damaged.

Check fuse

tube.

Flasher

Starting

relay

Control

switch

CAUTION

Summary of Contents for ZS250GY-3













































































Search results

Summary of Contents for ZS250GY-3

Reviews:

Related manuals for ZS250GY-3

Brands by name

Popular brands

ZONGSHEN ZS250GY-3, Service Manual

Search results

Summary of Contents for ZS250GY-3

Reviews:

Related manuals for ZS250GY-3

Brands by name

Popular brands