background image

6

© Copyright 2020 Zoeller

®

 Co. All rights reserved.

X71 Series Three Phase Installation

Single Phase Installation (X7110 & X7111 Only)

All single phase models require start capacitor, run capacitor and relay in the circuit to start and operate properly. These components can be 

purchased separately or prewired in a Zoeller control panel. For components purchased separately use the diagram for installation and hookup.
Single phase models are nonautomatic. To operate automatically a control panel  must be added to the power circuit. Follow the instructions 

provided with the panel.

WIRING DIAGRAM

COMPONENT LAYOUT

2

1

5

WHITE

PUMP

START

MAIN

BLACK

L2

WHITE

BLACK

RUN CAPACITOR

RED

START CAPACITOR

L1

T2

T1

3

2

1

GREEN

230 VAC 1ø

(SEE CHART)

(SEE CHART)

R

RELAY

START

MODELS

7110 / 7111

START CAP.

270-324UF 250V

RUN CAP.

50UF 370V

ZEPA0537C

5

2

1

WHITE

RED

PUMP

MAIN

START

L1

L2

BLACK

WHITE

230 VAC 1Ø

FROM CONTACTOR

START

BLACK

START

RELAY

CAPACITOR

RUN CAPACITOR

1

2

3

GREEN

Three phase pumps are nonautomatic. To operate automatically, a 

control panel with level control is required. Follow the instructions 

provided with the panel to wire the system.

Before installing a pump, check the pump rotation to insure that 

wiring has been connected properly to power source, and that 

the green lead of power cord (See wiring diagram), is connected 

to a valid ground, Momentarily energize the pump, observing the 

directions of kick back due to starting torque. Rotation is correct if 

kick back is in the opposite direction of rotation arrow on the pump 

casing. If rotation is not correct, switching of any two power leads 

other than ground, should provide the proper rotation. 

Refer to the wiring diagram supplied with specific electrical control 

panel for correct electrical cable termination locations.

NOTE 1:

 Sensor cable includes 5 leads; 2 leads for thermal sensor, 2 leads for 

moisture sensor, and a green ground lead. Sensor wire colors are as shown.

330K OHMS RESISTANCE

SEAL FAILURE PROBES

3 PHASE MOTOR

SEAL FAILURE MOISTURE SENSOR

LEADS MUST BE CONNECTED TO 

INDUCTION CIRCUIT IN THE CONTROL

PANEL.

THERMAL SENSOR

T1

T2

L1

L2

T3

L3

3Ø VAC

BLACK

GREEN

WHITE

SENSOR CABLE

RED

(N/C)

STARTER COIL

POWER CABLE

ORANGE

RECOMMENDED THERMAL SENSOR

CONNECTED IN SERIES WITH

ZEPA0038G

ZEPA0538

Summary of Contents for X71 Series









Reviews: