background image

11

Congratulations!  Your Fit

 is online. You can now open the product’s configuration by clicking the “View” button to modify the Fit’s device and 

notification settings.  

You can also install the Z Control

®

 mobile app on your mobile device (Android and iOS versions available, search “Z Control” in the app stores).  

This app allows for easy access to device information.  Silence, Reset, and Test functionality is also included.  The app is not currently designed for 

setting up WiFi, creating an account, or adding devices. These steps should be done through the web interface (using a mobile device to access 

the web interface is fine).

4.  Once the Fit’s Z Control

®

 LED is solid, log in to your account (or create one) at zcontrolcloud.com (see Figure D).  Click the Edit button next 

to a location, and choose Add New Device.  Follow the directions to add your Fit by either auto-detect or entering the Device I.D.  When 

successful, a Fit product tile will appear in your account.

When you add the correct 

Device ID, an Fit product tile 

will appear in your account

Select Add New Device

Figure D

© Copyright 2019 Zoeller

®

 Co. All rights reserved.

Summary of Contents for ProPak AQUANOT FIT 508/53













Reviews: