Zoeller 161-0059 Owner'S Manual Download Page 5

Page: 5 / 12

HAZARDOUS ENVIRONMENTAL PUMP DESCRIPTION

1. Pumps are constructed of class 30 cast iron with powder coated

epoxy protection for long life when pumping sewage in submersible

applications.

2. Pump motors are available in single and three phase design.

3. The Hazardous Environmental Pump is a single seal design and

has seal leak probes. Single phase units have an internal thermal

overload. Three phase pumps have a thermal sensor. A moisture

sensor seal fail circuit is incorporated into the control panel required

for nonautomatic pumps. Moisture sensor indicator panel, 10-1031,

is recommended but not required for automatic pump models.

4. Three phase pumps require overload protection in the control panel.

These pumps are to be repaired by firms approved

by Zoeller Company and in accordance to Policy # FM0212-3d.

Otherwise, they are to be returned to the factory for repair.

FIELD ASSEMBLED INSTALLATION

1. Contractor shall furnish all labor, material, equipment and

incidentals required for installation of hazardous environmental

pump.

2. Installation and piping instructions are included with the rail system

and basin instructions. If pump is being retrofitted to an existing

rail system, accessory parts may be required. Consult the factory

and advise make and model of rail system being used.

3. All electrical connections including pump to control box and power

supply to control panels must comply with the “National Electrical

Code” and applicable local codes. Installation of electrical panels

and connections should be made by a qualified licensed electrician.

4. When installing a pump with a check valve, or a rail system with

a check valve, you must give the pump case time to fill to help

prevent air lock when lowering the unit into the liquid. The 6404/6405

pump case has an air vent located behind the discharge. This air

vent is across the pump housing mounting surface and must be

cleaned before each reinstall. An air vent hole (3/16") must be

drilled in discharge pipe below the check valve to help prevent air

lock. This drilled hole must be cleaned before each reinstall. After

the pump is installed, run the unit submerged to assure the pump

case is filled (Water should come out of 3/16" diameter hole).

GENERAL INFORMATION

010740

Summary of Contents for 161-0059












Search results

Summary of Contents for 161-0059

Reviews:

Related manuals for 161-0059

Brands by name

Popular brands

Zoeller 161-0059, Owner'S Manual

Search results

Summary of Contents for 161-0059

Reviews:

Related manuals for 161-0059

Brands by name

Popular brands