background image

© Copyright 2005 Zoeller Co. All rights reserved.

Illustrated Parts Breakdown

Drain Pump 105 Pic tured

Drain Pump 104 Pic tured

2

7

4

5

8

6

1

9

10

11

3

12

CHECK VALVE

(PURCHASED
SEPARATELY)

13

SK2008B

10

11

9

2

5

12

3

7

4

1

8

6

13

SK2008A

 MODELS

105, 110, 115, 120

131

104

ITEM

DESCRIPTION

QTY

08/00

thru

Current

08/00

thru

Current

08/00

thru

Current

1 Drain 

Pump

1

105-0001

131-0001

104-0005

110-0001

N/A

N/A

115-0001

N/A

N/A

120-0001

N/A

N/A

2

Md. "M72" (See FM1722)

1

N/A

N/A

72-0001

 

Md. “M53” (See FM0472)

007917

N/A

N/A

“M55” (See FM0537)

    

007918

N/A

N/A

“M57” (See FM0431)

    

007919

N/A

N/A

“M59” (See FM0432)

    

007920

N/A

N/A

“M98” (See FM1032)

    

N/A

007921

N/A

3 Basin 

Tank

1

013017

013017

013017

4

Discharge Tube

1

013732

014759

013732

Basin - Lid

1

013018

013018

013018

6

Hard ware  Pack

1

013731

013731

013731

7 Basin 

Seal

1

N/A*

N/A*

N/A*

8 Unicheck

1

30-0181

30-0181

30-0181

¼ - 20X1" lg. RHM Screw S.S.  

8

N/A*

N/A*

N/A*

10 

¼ - Flat Washer S.S.      

16

N/A*

N/A*

N/A*

11 

¼ - 20 Hex. Hd. Nut - S.S.

8

N/A*

N/A*

N/A*

12

Pipe Cap w/o-ring 

1

N/A*

N/A*

N/A*

13

O-Ring

1

N/A*

N/A*

N/A*

 *When ordering this item order the hardware pack item #6.

Summary of Contents for 104









Reviews: