background image

 

3 / 9 

 E 
 N 
 G 

  

  

 S 
 H 

 

ASSEMBLY 

(WAVE 11) 

 

Choose a smooth and clean surface 

 

 

IF THE BUOYANCY TUBE WAS STORED AT A TEMPERATURE BELOW 

0°C / 32°F, LEAVE IT AT 20°C / 68°F FOR 12 HOURS BEFORE 

UNFOLDING.

 
 

  Sprinkle some starch in the angle (joint of the buoyancy tubes to the bottom) to facilitate fitting.

                              

CAUTION, NEVER USE TALCUM POWDER

 

 

Make sure you identify the parts and direction in which they fit: 

 

- The floorboard consists of 3 main sections and 2 sections in the bow [fig 1 and 4]. 

 

- The bow sections have an upside and a downside. 

 
1.  Insert the bow section (1) into the bow angle. 
2.  Insert the rear section (5) against the transom (6) as show on fig 1. 
3.  Fit all sections together [fig.1]. 
4.  Position sections 3 and 4 as an apex (in a tent-like position) [fig 1 and 2]. 
5.  Check that all sections are correctly aligned [fig 4]. 
6.  Check that the floorboard is correctly fitted in the angles. 
7.  Flatten the apex by standing on it (in the boat) and pulling the lifelines to prevent the fabric being 
pinched [fig. 2]. 
8.  Assemble the stringers (see instructions bellow). 
 
 
 
 

ASSEMBLY OF THE STRINGERS 

 
The stringers are essential to good working of the boat: they lock the floorboard together and rigidify 
its structure. 
 

1.

  To facilitate the fitting of the first stringer, slide the other stringer under the boat, about 20 cm     

(8’’) from the side [fig. 3-a].

 

 

 

 

 

DO NOT PUT THE STRINGER IN POSITION UNDER THE BOAT UNTIL 

THE FLOOR IS FLATTENED. 

 

2.

  Position the stringer on the edge of the floorboard. 

The thicker part should be towards the top

 

[fig. 3]. 

3.

  Fit the stringers between the two buffers (9) of sections 3 and 5 [fig. 4]. 

4.

  Rotate the stringer in the angle so as to press them against the bottom [fig. 3-b and 4]. 

5. 

Because of the self-locking system of the floorboard, the stingers will fit into place once the 
buoyancy tube is inflated. 

 

Summary of Contents for Wave

















Reviews: