background image

1

H0360700.D - EN - 2016-02

 

WARNINGS

•  Failure to respect the warnings may cause serious damage to the pool equipment or cause serious injury, 

even death.

•  

The appliance is intended for a specifi c pool use and must not be used for any use other than that for which 

it was designed.

•  

It is important that the equipment is operated by competent and qualifi ed (both physically and mentally) 

people who have previously received the instructi ons for use. All persons not meeti ng these criteria must not 

approach the appliance in order to avoid exposure to dangerous elements.

•  Keep the appliance out of the reach of children.

•  

The  device  must  be  installed  by  a  qualifi ed  technician  according  to  the  manufacturer’s  instructi ons  and 

in compliance with local regulati ons. The installer is responsible for installati on of the equipment and for 

compliance with nati onal installati on regulati ons. Under  no circumstances  can the  manufacturer  be  held 

liable in the event of failure to comply with applicable local standards.

•  

Incorrect installati on and/or use may cause serious damage to property or serious injuries (possibly causing 

death). 

•  All equipment, even postage and packing paid, travels at the risks and perils of the recipient. The consignee 

shall make reservati ons in writi ng on the carrier's bill of lading if damage is detected, caused during transport 

(confi rmati on to be sent to the carrier within 48 hours by registered mail with acknowledgement of receipt). 

In the event of a device containing coolant that has been turned on its side, menti on your reservati ons in 

writi ng to the carrier.

•  

If the appliance suff ers a malfuncti on, do not try to repair the appliance yourself, contact a qualifi ed technician.

•  

Refer to the warranty conditi ons for details of the permitt ed water balance values for operati ng the appliance.

•  

Eliminati ng or shunti ng one of the safety devices automati cally voids the warranty, as does the replacement 

of parts using parts not manufactured by ourselves.

•  

Do not spray insecti cide or any other chemical (infl ammable or non-infl ammable) in the directi on of the 

appliance, as this may damage the body and cause a fi re.

•  

The electrical supply to the appliance must be protected by a dedicated 30 mA diff erenti al residual current 

protecti on device, complying with the standards and regulati ons in force in the country where it is installed.

•  

Before carrying out any operati ons, check that:

 

-

The voltage indicated on the maker's plate of the appliance corresponds to the mains voltage, 

 

-

The power grid is adapted to the power requirements of the appliance, and is grounded. 

 

-

The plug (where applicable) is suitable for the socket.

•  

In the event of abnormal functi on or the release of odours from the appliance, turn it of immediately, unplug 

it from its power supply and contact a professional.

•  

Before any interventi on on the appliance, ensure that the latt er is switched off  and disconnected from the 

power supply, in additi on to any other equipment connected to the appliance, and that the heati ng priority 

(where applicable) is deacti vated.

•  

Do not disconnect and reconnect the appliance to the power supply when in operati on.

•  Do not pull on the power cord to disconnect it from the power supply.

•  Do not handle the electrical elements with wet hands.

•  

Clean the terminal board or the power supply socket before connecti on.

•  

For any component or sub-assembly containing a batt ery: do not recharge or dismantle the batt ery, or throw 

it into a fi re. Do not expose it to high temperatures or direct sunlight.

•  

In stormy weather, unplug the appliance to prevent it from suff ering lightning damage.

•  

Do not immerse the appliance in water (with the excepti on of cleaners) or mud.

Recycling

This symbol means that your appliance must not be thrown into a normal bin. It will be selecti vely collected for the 

purpose of reuse, recycling or transformati on. If it contains any substances that may be harmful to the environment, 

these will be eliminated or neutralised.

Contact your dealer for recycling informati on.

EN

Summary of Contents for Uranus+

















Reviews: