![background image](http://html1.mh-extra.com/html/zodiac/exo-10/exo-10_instructions-for-installation-and-use-manual_936564056.webp)
54
Message
Possible cause
Soluti on
(NO MESSAGE)
No visible chlorine
producti on on the
cell plates.
•
Chlorinati on is in the reversal period.
•
Chlorinati on is set to less than 100% and
is stopped.
•
Wait and see. Chlorinati on should resume
within the next 10 minutes.
(NO MESSAGE)
Data loss (ti me,
etc.)
•
Dead batt ery
• Power cut
•
Do not reprogram the following informati on:
ti me, language, appliance type.
• Contact your retailer
to
replace the 3V
CR1220 batt ery.
•
Wait for the power to be restored.
==> The appliance should automati cally recover
the informati on saved before the power cut.
8.1.2 Appliance WITH pH Link or Dual Link module
Message
Possible cause
Soluti on
"pH LOW"
(
“INFO”
indicator
lit)
•
The pH is less than 5.
•
Faulty connecti on or calibrati on error, pH
sensor failure or dirty.
•
Low alkalinity, reduced pH.
•
Check the pH sensor wiring on the control box
and on the sensor holder.
•
Check the operati on of the sensor using a
sensor tester (contact your retailer)
.
•
Clean and calibrate the sensor.
•
Check and adjust the alkalinity.
•
Replace the sensor.
"pH REGUL.
STOP"
(
“INFO”
indicator
fl ashing)
•
The pH setpoint has not been reached aft er
5 consecuti ve hours of injecti on.
•
Faulty connecti on or calibrati on error, pH
sensor failure or dirty.
•
The pH minus container is empty.
•
The peristalti c pump is not primed.
•
High alkalinity, injecti on of acid does not
reduce the pH.
•
Check the pool's pH using a photometer or a
test strip.
•
Check the pH sensor wiring on the control box
and on the sensor holder.
•
Check the operati on of the sensor using a
sensor tester (contact your retailer)
.
•
Clean and calibrate the sensor.
•
Replace the pH container.
•
Test the peristalti c pump (contact your retailer)
.
•
Reduce the alkalinity level (contact your
retailer)
.
•
Replace the pH sensor.
"ORP PROD.
STOP"
(
“INFO”
indicator
fl ashing)
•
The ORP setpoint has not been reached
aft er 36 consecuti ve hours of chlorinati on.
•
Faulty connecti on or calibrati on error, ORP
sensor failure or dirty.
•
A too high concentrati on of cyanuric acid
signifi cantly reduces the effi cacy of the
chlorine.
•
A too high concentrati on of cyanuric acid
reduces the ORP measurement taken by
the sensor.
•
pH too high.
•
If the total chlorine concentrati on is too
high, the chloramines reduce the ORP
measurement taken by the sensor.
•
The appliance is not appropriate for the size
of the pool.
•
When the cell is worn, scaled up or
defecti ve, the electrolysis reacti on does not
occur correctly.
•
Check the pool's chlorine level using a
photometer or a test strip.
•
Check the ORP sensor wiring on the control
box and on the sensor holder.
•
Check the operati on of the sensor using a
sensor tester (contact your retailer)
.
•
Clean and calibrate the sensor.
•
Empty the pool using the bott om drain to
reduce the concentrati on of cyanuric acid.
•
Perform shock chlorinati on (with calcium
hypochlorite) to reduce the concentrati on of
chloramines.
•
Check the conditi on of the cells.
•
Replace the ORP sensor.