background image

11

3.3 I Starting the appliance

The appliance must have filters fitted when operating.

Avoid opening doors and windows when using the appliance.

Power on the device by plugging in the power cable,

Press the button   : the fan speed and desired humidity level indicators light up (last active settings),

Set the desired humidity level using the "HUMIDITY" button (40%, 50%, 60%, 70%) or set the appliance to continuous

operation using "CNT",

The  continuous  operating  mode  does  not  take  humidity  levels  into  account:  the  device  operates

continuously.

Adjust the speed of the fan with the "SPEED" button.

Check that the appliance is draining condensates when in operation (see "2.1.3 Connecting the condensate drainage

line").

After a 5 minute delay, if the level of ambient humidity is higher than the desired humidity level, the

compressor starts up and the "COMP." indicator lights up.

A comfortable humidity rate for pool use is 60%.

Ventilation is permanent while the appliance is switched on.

The  dehumidifier  is  equipped  with  a  defrosting  system  which  starts  automatically  as  soon  as  frost

forms during low temperatures. The compressor automatically starts-up or stops based on the ambient

temperature. The fan operates continuously.

When the humidity level is less than 35% in continuous operation mode, the appliance permanently

displays "LO" but the compressor and the fan continue to operate at the selected speed. Switch off the

appliance or select a humidity rate so that it rises to the ideal or desired rate.

Summary of Contents for DT850E




















Reviews: