background image

HydroTap Installation and Operating Instructions_Commercial_BCH 4in1_BH 3in1_October 2012_V1.05 

                   Page 6 of 24

Read These Warnings 

continued

Altitude 

The Zip HydroTap is equipped with a self-calibrating program which caters for 
altitude adjustment.

Filter Control 

The Zip HydroTap filter control is preset to 6000 litres to provide trouble-free flow 
and operation in most installations. Local water quality conditions may require an 
alteration to this capacity. In areas where the water has a high concentration of 
sediment, the preset litre capacity may be shortened to avoid poor flow, taste or 
odour situations. In areas where the water quality is above average, lengthening 
the preset capacity may be desirable, but not essential. If any of these changes is 
needed, follow the instructions on page 16 or contact your Zip Service Provider.

Frost Protection

If this appliance is located where the ambient air temperature could fall below 

5ºC when the heater is not in use, do not turn off the appliance electrically. This 

safeguard does not offer the same protection to the connecting pipework and 

fittings.

Environment Considerations

This unit is intended for indoor use only and should never be installed outdoors or 
exposed to the elements of nature. This unit must not be positioned in an area that 
may be cleaned by a water jet and must not be cleaned by a water jet.

Warning:

Zip HydroTaps are designed to operate within 1ºC to 2ºC of set point for boiling 
water and at 5ºC to 15ºC for chilled drinking water. All boiling water units are 
self calibrating to 98ºC, which is the recommended setting. Adjustments to the 
recommended setting of 98ºC setting are not advised, however, under certain 
circumstances adjustments may be made between 68º - 100ºC . The 100ºC setting 
is not recommended as units may discharge or boil over more frequently. 

For details see step G on page 12. 

Caution 

must be observed when changing any settings within the Service 

Menu as any changes may affect the normal operation of the unit.

Note:

Always ensure the silicone tubes are shortened so that any excess is removed 

and their route is the most direct line between the tap assembly and the 

HydroTap unit.
Do not allow the tubes to sag or droop so water is trapped within the hoses. 

Always maintain a constant fall.
Positioning of the tap assembly must be within the following parameters:
The height between the base of the Hydrotap unit and the base of the Tap 

assembly cannot be greater than 900mm.

Summary of Contents for HydroTap 4-in-1

























Reviews: