Zimmer GEP2000IL-03 Page 35 Installation And Operating Instructions Manual Download

Page: 35 / 40

Zimmer GmbH

•

Im Salmenkopf 5

•



77866 Rheinau, Germany

•



+49 7844 9138 0

•



+49 7844 9138 80

•

www.zimmer-group.com

INSTALLATION AND OPERATING INSTRUCTIONS:

2-jaw parallel gripper, electric, GEP2000IL-03 series

EN / 2021-03-04

DDOC01219 / 0

Error code

Error

Possible cause

Measure

0x309

"TeachPosition" not transferred. • Process data sent by the

master has been changed.

►

Confirm the newly transmitted

process data with a

"Handshake" "ControlWord" =

0x1.

0x30D

"GripForce" not transferred.

• Process data sent by the

master has been changed.

►

Confirm the newly transmitted

process data with a

"Handshake" "ControlWord" =

0x1.

0x30E

"DriveVelocity" not transferred.

• Process data sent by the

master has been changed.

►

Confirm the newly transmitted

process data with a

"Handshake" "ControlWord" =

0x1.

0x30F

"TeachTolerance" not trans-

ferred.

• Process data sent by the

master has been changed.

►

Confirm the newly transmitted

process data with a

"Handshake" "ControlWord" =

0x1.

0x310

"DeviceMode" not applied.

• Process data sent by the

master has been changed.

►

Confirm the newly transmitted

process data with a

"Handshake" "ControlWord" =

0x1.

0x311

Initial "Handshake" is missing.

• Process data sent by the

master has been changed.

►

Confirm the newly transmitted

process data with a

"Handshake" "ControlWord" =

0x1.

0x312

“WorkpieceNo." not available.

• After a cold boot, a one-time

data transfer via ControlWord =

1 must be carried out.

►

Confirm the current process

data with a "Handshake,"

ControlWord = 0x1.

0x314

"BasePosition" greater than

"WorkPosition"

• Transferred "BasePosition" is

greater than or equal to the

transferred "WorkPosition."

►

Check the transmitted process

data

0x400

Gripper is jammed.

•

Gripper is difficult to move.

• Travel path of the gripper is

impeded.

►

Restore the ease of movement

of the gripper.

►

Reset via "ControlWord" =

0x8000

0x406

System error

• Internal system error

►

Contact Zimmer Customer

Service.

0x40B

Gripper-internal parameters are

not consistent.

• Incompatible or damaged

parameters were loaded.

►

Contact Zimmer Customer

Service.

Summary of Contents for GEP2000IL-03









































Search results

Summary of Contents for GEP2000IL-03

Reviews:

Related manuals for GEP2000IL-03

Brands by name

Popular brands

Zimmer GEP2000IL-03, Installation And Operating Instructions Manual

Search results

Summary of Contents for GEP2000IL-03

Reviews:

Related manuals for GEP2000IL-03

Brands by name

Popular brands