Zimmer DES Series Installation And Operating Instructions Manual Download Page 22

Page: 22 / 54

11.2.5 Referencing the motor encoder
INFORMATION

While in the

Module

operation mode, the product has a continuous travel range.

The travel range can be limited in degrees via the

IndraWorks Ds

software.

►

In the navigation pane, click

Motor, Brake,

Measurement Systems

►

Click

Motor encoder

►

Click

Motor Encoder Position reference

►

Enter the reference measurement in the

Reference measurement

field.

►

Disable the release for the drive control unit.

►

Click the

Set Absolute Position

button.

The product references itself to the entered

reference measurement.

►

Move the product in Easy Startup mode

after the reference position has been

adopted.

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

INSTALLATION AND OPERATING INSTRUCTIONS:

DES

DDOC00192 / f

EN / 2022-07-20

Summary of Contents for DES Series























































Search results

Summary of Contents for DES Series

Reviews:

Related manuals for DES Series

Brands by name

Popular brands

Zimmer DES Series, Installation And Operating Instructions Manual

Search results

Summary of Contents for DES Series

Reviews:

Related manuals for DES Series

Brands by name

Popular brands