Zimmer DES Series Installation And Operating Instructions Manual Download Page 20

Page: 20 / 54

The name of the parameter set is displayed

in the navigation pane after the parameter

set has been transmitted successfully.

►

Eliminate all errors so that the product can

be moved.

►

In the

Diagnostics

menu, click

Axis status

Status messages are displayed in the

window.

►

Click the

Clear Error

button to acknowledge

the error messages.

11.2.4 Moving the product in Easy Startup mode

The product can be moved in Easy Startup mode as soon as it is ready to be operated.

►

In the navigation pane, click

Optimization/

Commissioning

►

Click

Easy Startup Mode

The

Easy Startup Mode

area is displayed.

►

Click the

Start Easy Startup Mode

button.

Easy Startup mode has been started.

The status pane of Easy Startup mode is

enabled.

►

Click the

Enable

button.

The window with warning notices is

displayed.

►

Please read all notices carefully and follow

each of these notices.

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

INSTALLATION AND OPERATING INSTRUCTIONS:

DES

DDOC00192 / f

EN / 2022-07-20

Summary of Contents for DES Series























































Search results

Summary of Contents for DES Series

Reviews:

Related manuals for DES Series

Brands by name

Popular brands

Zimmer DES Series, Installation And Operating Instructions Manual

Search results

Summary of Contents for DES Series

Reviews:

Related manuals for DES Series

Brands by name

Popular brands