background image

INSTALLATION AND OPERATING INSTRUCTIONS:

 Collision protection, pneumatic, CSR series

5

Zimmer GmbH 

 Im Salmenkopf 5 

 77866 Rheinau, Germany 

 

 

+49 7844 9138 0 

• 

 +49 7844 9138 80 

 www.zimmer-group.com

EN / 2020-09-15

DDOC00267 / b

3  Proper use

NOTICE

The product is only to be used in its original state with its original accessories, with no unauthorized changes and 

within the stipulated parameter limits and operating conditions. Any other or more extensive use is improper.

 

Operate the product only in compliance with the associated installation and operating instructions.

 

Operate the product only when it is in a technical condition that corresponds to the guaranteed parameters 

and operating conditions.

 

Ö

Zimmer GmbH shall accept no liability for any damage caused by improper use. The user bears sole respon-

sibility.

Use outside of the defined parameters is not permitted. Unauthorized electrical or mechanical modifications must not be 

made.
The product is not suitable for use as an active compensation module.
Direct contact with perishable goods/food is not permitted.

Personnel qualification

Installation, commissioning and maintenance may only be performed by qualified personnel. These personnel must have 

read and understood the installation and operating instructions in full.

5  Product description

5.1  Forces and torques

INFORMATION

For information on the forces and torques for the following product, please refer to our website at 

www.

zimmer-group.com:

•  CSR series
Please contact Zimmer Customer Service if you have any questions.

5.2  Type plate

A type plate is attached to the housing of the product (see 

the image on the right for an example). The article number 

and the confirmation number are shown on the type plate.
The confirmation number is assigned to the project. This 

ensures unambiguous and consistent classification in the 

event of an update or an overhaul. 

 

Ö

Example of an article number: 

dl

 

Ö

Example of a confirmation number: 

dm

XXX

XX-XXXXXX

dl

dm

INFORMATION

Please state the confirmation number in the event of damage or a complaint.

Please contact Zimmer Customer Service if you have any questions.

Summary of Contents for CSR Series













Reviews: