Zhermack vap 8, User Manual

Page: 28 / 104

VAP 8 / 8A - AD 8
EN
28
The reference figures can be found on pages 3, 4, 5, 6 of this manual.
CHAPTER 5: TRANSPORT AND HANDLING
5.1 GENERAL WARNINGS
• In order to prevent injury/damage to persons/
objects, pay great care when handling the
equipment, scrupulously complying with all
precautions and instructions contained in the
following paragraphs.
• The generator must be handled and/or moved
by at least 2 (two) people, holding the appliance
at the bottom.
5.2 PACKAGING AND UNPACKING
Fig. D: All material is carefully controlled by the
Manufacturer before delivery. On receiving the equipment,
make sure that it has not been damaged during transport
and that the packaging has not been tampered with,
resulting in missing parts.
Should any damage or missing parts be noted, inform
the Dealer and the Carrier immediately by forwarding
photographic evidence. The packaging, made up of a
cardboard box with expanded plastic internal protections,
contains:
• the equipment VAP 8 or VAP 8A and eventually the
softener AD 8;
• the material supplied (see par. 4.2.1);
• the Use and Maintenance Manual.
• It is recommended that you keep the original
packaging (see paragraph 5.3).
• The customer is responsible for ensuring that
the product delivered to the manufacturer
is properly packaged. The manufacturer
is not liable for any defects, malfunctions
or damage to the product due to the use
of packaging that is not suitable or of the
same or higher quality than that used for the
original delivery.
5.3 TRANSPORT AND HANDLING
Should it be necessary to move the equipment proceed
as follows:
• disconnect the equipment from the mains power
supply;
• if necessary, empty the boiler (see section 8.3.1);
• (VAP 8A) disconnect the water softener hose (22) - if any
- from the water inlet connector (20);
• disconnect the other softener hose (23) from the water
supply tap;
• hold the equipment, always keeping it in a vertical
position. Regarding this, pay attention to the weight and
clearance of the equipment (see par. 4.2.2), in order to
prevent any type of damage occurring due to the failure
of considering these values;
• pack the equipment in the original packaging. If this is
not possible, take all necessary precautions to protect
the equipment from knocks and drops, as the goods are
transported at the owner’s risk.
Failure to comply with the rules stated above
relieve the Manufacturer from any liability
regarding equipment malfunctioning and
consequently makes the warranty null and void.
When shipping and/or delivering the equipment
to an Authorised After-Sales Centre always enclose
a copy of the purchase document and a copy of
the properly filled-in identification form. If the
equipment is transported by carrier, the Postal
Service or rail, it is recommended to insure the
shipment.
5.4 DISPOSAL / DISMANTLING
When disposing of the packaging material the user must
follow the regulations in force in the country of use
relative to the following materials:
• wood/paper: non-polluting materials, but must be
re-cycled correctly;
• polystyrene/plastic: pollutant material, do not burn
(toxic fumes) or dispose of in the environment. Dispose
of these materials in compliance with the regulations in
force in the country of use.
If the equipment is to be dismantled, the operator must
be in charge of dismantling, elimination and re-cycling
of the following materials in compliance with the EEC
Directives and the laws in force in the country of use:
• plastic parts; steel parts; glass parts; insulated electric
cables; rubber parts.
• there are no toxic or corrosive substances.
The device must not be disposed of as urban
waste. At the end of its working life, it must be
taken to a waste separation and recycling
centre in compliance with European Directive
no. 2012/19/UE or in accordance with the
legislation in force in the country of sale.
CHAPTER 6: INSTALLATION AND COMMISSIONING
6.1 WARNINGS AND PRECAUTIONS
Before carrying out installation, make sure that all safety
conditions exist and follow the indications given below
carefully.
6.2 ACCEPTED ENVIRONMENTAL CONDITIONS
Unless stated otherwise, at the time of ordering, it
is intended that the equipment must be envisioned
to function regularly in the following environmental
conditions:
Place of Use Indoors
Altitude Up to 2000 m
Working temperature From 10°C to 35°C
Humidity Max 80%
Conditions different to those prescribed can cause
anomalies or sudden breakdown. Lighting in the
installation area of the equipment must be sufficient to
guarantee good visibility in all points of the equipment.