Zetor MAJOR HS Series Operator'S Manual Download Page 37

Page: 37 / 140

Road and reduced speeds shifting lever

Hand brake lever

Hydraulics control panel

Auxiliary hydraulic switchboard control

Road and reduced speeds shifting lever serves for shifting
gear groups.

Gear shifting is done with the tractor at standstill and
depressed clutch pedal.

H Road

speeds

Average speeds

N Neutral
L Reduced

speeds

MHS16N016

The hand brake lever is located on the right left of the
driver's seat.

MHS16N018

The hydraulic control panel with levers (A) is located in the
compartment of the right mudguard.
The controls of the hydraulics (B) are located in front of
the levers.

MHS16N012

Auxiliary hydraulic switchboard control is placed on the
upper part of right fender.

MHS16N013

ACQUAINTANCE WITH THE TRACTOR

Summary of Contents for MAJOR HS Series













































































































































Search results

Summary of Contents for MAJOR HS Series

Reviews:

Related manuals for MAJOR HS Series

Brands by name

Popular brands

Zetor MAJOR HS Series, Operator'S Manual

Search results

Summary of Contents for MAJOR HS Series

Reviews:

Related manuals for MAJOR HS Series

Brands by name

Popular brands