manualshive.com logo in svg

Zetor MAJOR HS Series, Operator'S Manual

Share
Download
Zetor MAJOR HS Series Operator'S Manual Download Page 24

 

Liquid brakes 

Trailer brakes 
 

Air brakes of the trailer  
Check tightness of the air-brake system and braking efficiency of the tractor with the trailer. 

 

   Decrease of air pressure in the air pressure system of brakes below the critical limit is 

indicated by an error message on the instrument panel. More information in chapter Driving. 
 

Hydraulic brakes of the trailer  
Check tightness of hygraulic-brake circuits in the trailer and braking efficiency of the tractor with the trailer.  

Hitches 

Inspection of fouling of coolers 
Open the front cowl and check the plates of the engine radiator of engine cooling liquid and air conditioning 
condenser, the cooler of oil of the front PTO shaft and the cooler of the gear oil (if the tractor is equipped with 
them) for fouling. 
In case of fouling clean the cooler plates with pressure air.

 

 

Check the liquid brakes for leaks as well as the liquid 
control of the clutch and the braking liquid level in the 
expansion tank.  
Maintain the brake liquid level in the range of 3/4 of the 
tank content (max. level) and 1/2 of the tank content 
(minimum level).  

MHS16N050

 

 

Check the condition of the hitching and attachment 
systems of the tractor and trailer.  

NM13N063

 

 

 PREVENTIVE DAILY MAINTENANCE

23

Summary of Contents for MAJOR HS Series













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands