BNP
®
65 and 220 SUCTION BLAST CABINETS
Page 1
© 2019 CLEMCO INDUSTRIES CORP.
www.clemcoindustries.com
Manual No. 21309, Rev. J 01/19
1.0
INTRODUCTION
1.1
Scope of Manual
1.1.1
These instructions cover setup, operation,
maintenance, troubleshooting, optional accessories, and
replacement parts for the following BNP
-
65 and 220
Suction Blast Cabinets:
BNP-65S ............. Conventional (stand-up model)
BNP-65SE ............... Ergonomic (sit-down model)
BNP-220S ........... Conventional (stand-up model)
BNP-220SE ............. Ergonomic (sit-down model)
The instructions cover the operation of all pull-thru
reclaimers and the installation of the dust collector. One
of the following supplemental manuals is provided with
the dust collector. Refer to the appropriate manual for
operation and maintenance of the collector:
CDC-1 Dust Collectors ..... manual stock no. 28225
RPC-2 Dust Collector ....... manual stock no. 22788
RPH-2 Dust Collector ....... manual stock no. 21449
1.1.2
The instructions contain important information
required for safe operation of the cabinet. Before using
this equipment, all personnel associated with the blast
cabinet operation must read this entire manual and all
accessory manuals to become familiar with their
operation, parts, and terminology.
1.2
Safety Alerts
1.2.1
Clemco uses safety alert signal words, based on
ANSI Z535.4-2011, to alert the user of a potentially
hazardous situation that may be encountered while
operating this equipment. ANSI's definitions of the signal
words are as follows:
This is the safety alert symbol. It is
used to alert you to potential physical
injury hazards. Obey all safety
messages that follow this symbol to
avoid possible injury or death.
NOTICE
Notice indicates information that is considered
important, but not hazard-related, if not
avoided, could result in property damage.
CAUTION
Caution indicates a hazardous situation that, if
not avoided, could result in minor or moderate
injury.
WARNING
Warning indicates a hazardous situation that, if
not avoided, could result in death or serious
injury.
DANGER
D
anger indicates a hazardous situation that, if
not avoided, will result in death or serious
injury.
1.3
Table of Contents
SUBJECT
SECTION LOCATION
INTRODUCTION ....................................................... 1.0
Scope of Manual ........................................................ 1.1
Safety Alerts ............................................................... 1.2
Table of Contents ...................................................... 1.3
General Description ................................................... 1.4
Theory of Operation ................................................... 1.5
Reverse-Pulse Dust Collector Options ...................... 1.6
Nozzle Options .......................................................... 1.7
Reclaimer Options ..................................................... 1.8
Blasting Media ........................................................... 1.9
Compressed-Air Requirements ............................... 1.10
Electrical Requirements ........................................... 1.11
INSTALLATION ........................................................ 2.0
General Installation Notes ......................................... 2.1
Connect Conveying (flex) Hose ................................. 2.2
Connect Compressed-Air Supply Lines ..................... 2.3
Ground the Cabinet and Dust Collector ...................... 2.4
Connect Electrical Service ......................................... 2.5
Single-phase wiring .............................................. 2.5.1
Three-phase wiring ............................................... 2.5.2
Connect Media Hose (900 cfm reclaimer only) .......... 2.6
Set Air-Inlet Damper .................................................. 2.7
Final Assembly ........................................................... 2.8
FIELD INSTALLED ACCESSORIES ........................ 3.0
Aluminum Oxide (aggressive media) Kit ................... 3.1
Cabinet Curtains Installation ...................................... 3.2
Manometer ................................................................. 3.3
Armrest ...................................................................... 3.4
Turntable with Workcar and Track ............................. 3.5
Optional Externally Adjustable Vortex Cylinder ......... 3.6
OPERATION .............................................................. 4.0
Media Loading ........................................................... 4.1
Media Unloading ........................................................ 4.2
Loading and Unloading Parts .................................... 4.3
Blasting Operation ..................................................... 4.4
Blasting Technique .................................................... 4.5
Stop Blasting .............................................................. 4.6
Shutdown ................................................................... 4.7
