background image

Head Office : 1-9 Minamidai, Kawagoe-city, Saitama, 350-1192 Japan

Phone: (+81)49-243-1115  Fax: (+81)49-243-7197

11. Warranty

1) SCOPE OF APPLICATION 

This engine manufactured by Komatsu Zenoah Co. (hereinafter referred as KZ) and

sold to the user directly or through distributor/manufacturer, shall entitle to be covered

by this warranty. 

2) LIMIT OF WARRANTY 

KZ warrants that ; 

1. The quality disclosed in the specifications. 

2. The engine which shall be considered defective by KZ, caused by material or

production fault. 

3) LIMITS OF COMPENSATION 

1. KZ compensates such quality, material and production faults by repairing or

replacing. 

2. KZ shall not compensate any other accompanied or benefit losses caused to user

and distributor/manufacturer by such faults and through repairing or replacing. 

4) TERMS OF WARRANTY 

3 months after purchased by user subject to 12 months from produced month. 

5) EXEMPT FROM WARRANTY 

KZ shall not warrant this engine even if the fault has been caused during the period of

terms of warranty, in case of that ; 

1. Any faults, failures caused from neglect of this OWNER'S SERVICE MANUAL for

proper operation and maintenance. 

2. Any modifications not approved by KZ. 

3. Normal abrasion and deterioration. 

4. Consuming parts. 

Summary of Contents for Komatsu G260RC





















Reviews: