background image

11

English

3. SAFETY PRECAUTIONS

J. Do not charge the battery in a

humid place such as a bathroom
or in an open-air place exposed to
rain. Failure to observe this
warning might result in electric
shock, fire, or excessive heat
generation.

When charging the battery, do not
use an extension cord and do not
plug too many leads for other
electric appliances into one outlet.
Failure to observe this warning
might result in electric shock, fire,
or excessive heat generation.

Do not impair, damage, process,
forcibly bend, pull, twist, or bundle
the power supply cord. Do not put
anything heavy on it and do not insert
anything into it. Failure to observe
this warning might damage the power
supply cord or cause an electric
shock or fire.

If battery fluid splashes on your skin
or clothes, wash it away with clean
water immediately. Failure to do so
might result in skin irritation or
damage.

A. While charging the battery, do not

keep touching the same part of
your body to the charger for a long
time. The temperature of the
battery case could become high
enough to cause mild burns.

B. When not charging the battery, be

sure the AC adapter is unplugged
from the power supply outlet.
Failure to observe this precaution
might result in electric shock or fire
due to deterioration of the
insulation.

C. Be careful that the power supply

cord is not caught in a door or a
door sash. Failure to observe this
caution might result in damage to
the power supply cord and a risk
of electric shock or fire.

WARNING

WARNING

j.욕실  등  습기가  많은  곳이나,  실외

의 빗물에 젖는 곳에서는 충전하지 
마십시오.  감전,  발화,  이상발열의 
우려가 있습니다.

●충전할  때에는  연장코드를  사용하

거나  다른  전기제품과의  문어발식 
배선을  하지  마십시오.  감전,  이상
발열, 화재의 우려가 있습니다.

●전원코드를  손상시키거나,  파손하

거나, 가공하거나, 무리하게 굽히거
나,  잡아당기거나,  비틀거나,  묶거
나 하지 마십시오. 또한, 무거운 물
건을  올리거나  끼워넣지  마십시오. 
코드가 파손되어 감전, 화재의 원인
이 됩니다.

●밧데리액이  피부나  의류에  부착되

었을  경우,  바로  깨끗한  물로  씻어 
주십시오. 피부에 손상을 입힐 우려
가 있습니다.

a.충전기  안쪽은  신체의  동일부분이 

장시간 접촉되지 않도록 주의해 주
십시오. 케이스의 온도가 높아지는 
경우가 있어 저온화상을 입을 우려
가 있습니다.

b.충전하지  않을  때에는  반드시  AC

어뎁터를  콘센트에서  뽑아  주십시
오.  절연열화에  의한  감전이나  누
전화재의 원인의 됩니다.

c.전원코드가  문이나  샷시  등에  끼지 

않도록  각별히  주의해  주십시오. 
코드를  손상시켜  감전이나  발화의 
우려가 있습니다.

Summary of Contents for BK2650DL-Hb

























































Reviews: