OPERA
TION
25
VCR Mode Tape Playback
Normal Playback
Preparation:
Turn on the TV.
Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to VIDEO.
Set the Output Source to VCR as shown in Selecting the
Input/Output Source on page 15.
11
Insert a prerecorded video cassette.
The
indicator will light and the DVD+VCR will
power-up automatically.
Make sure that the TIMER indicator in the display
window is not lighted. If it is, press
POWER
once.
If a tape without a safety tab is inserted, the unit will
start playback automatically.
2
2
Press PLAY (
N
) once.
PLAY appears on the TV screen .
It is not necessary to select the tape speed for play-
back. It will be automatically selected by the DVD+VCR.
In playback, the
TV/VCR
selector switches to VCR
mode automatically.
3
3
Press STOP (
x
) to stop playback.
STOP appears on the TV screen.
If the tape reaches the end before STOP (
x
) is
pressed, the DVD+VCR will automatically stop, rewind
and eject the tape, and turn itself off.
Tracking Control
Auto Tracking
The automatic tracking function adjusts the picture to
remove snow or streaks.
The AUTO TRACKING function works in the following
cases:
A tape is played back for the first time.
Tape speed (SP, LP, EP) changes.
Streaks or snow appear because of scratches on the tape.
Manual Tracking
If noise appears on the screen during playback, press
either CH/TRK (
v
/
V
) on the remote control or
CH/PRESET (
v
/
V
) on the front panel until the noise on
the screen is reduced.
In case of vertical jitter, adjust these controls very carefully.
Tracking is automatically reset to normal when the tape is
ejected or the power cord is unplugged for more than 3 sec-
onds.
Special Effect Playback
Special effects playback notes
Horizontal lines (noise bars) will appear on the TV screen. This
is normal.
The audio is automatically muted during special effect modes,
so there is no sound during search.
During the high-speed picture search modes, a short time is
needed to stabilize tape speed when re-entering the PLAY
mode. Slight interference may be observed during this time.
Search
This function lets you quickly and visually search for a
desired tape section in either direction: forward and
reverse.
1
Press BACKWARD (
.
) or FORWARD (
>
)
during playback.
The DVD+VCR will be activated in the SEARCH
mode.
If the DVD+VCR is left in the SEARCH mode for more
than 3 minutes, the DVD+VCR will automatically enter the
PLAY mode, to protect the tape and video heads.
2
To return to playback, press PLAY (
N
).
Still Picture and Frame-by-Frame Playback
1
Press PAUSE/STEP (
X
) during playback.
A still picture appears on the TV screen.
If a still picture vibrates vertically, stabilize it by using
CH/TRK (
v
/
V
) on the remote control.
If the DVD+VCR is left in the STILL mode for more than 5
minutes, the DVD+VCR will automatically enter the STOP
mode to protect the tape and video heads.
2
Press PAUSE/STEP (
X
) repeatedly to advance the
video picture one frame at a time while viewing a still
picture.
3
To return to playback, press PLAY (
N
).
Slow Motion
1
While in still mode, press FORWARD (
>
).
The tape will be played back at a speed 1/19 times
slower than the normal speed.
During slow playback, use CH/TRK (
v
/
V
) on the Remote
Control to minimize noise bands.
If slow motion mode continues for more than 30 seconds,
the DVD+VCR will automatically change to playback
mode.
2
To return to playback, press PLAY (
N
).
CM SKIP (Commercial Skip)
This is useful for skipping commercials or short program
segments.
1
Press CM SKIP in playback mode.
The tape will fast forward picture search through 30
seconds of recording.
Skipping time can be extended by using CM SKIP.
Subsequent presses result in advancing the fast forward
picture search time by 30-second increments (maximum 2
minutes).
2
When the search is complete, the DVD+VCR will go
into playback mode automatically.
