Zelmer ZVC425 Series, User Manual

Page: 49 / 51

49
ZVC425-004_v01
SAFBAG dust bag disassembly/assembly
E
1 The vacuum cleaner is equipped with safety valve
located in chamber of dust container (bag). It opens
automatically in case of total stopping of suction hose or
total stopping of equipment elements connected thereto, as
well as in case of overfill of dust bag. After opening the valve
one can hear characteristic “whirr” sound inside the vacuum
cleaner.
2 Total covering up of bag loading indicator by the red
cover in case the sucker or the brush is upraised over
the cleaned surface informs, that change of dust bag is
necessary. The bag loading indicator may operate in case
of suction hose stopping or in case of stopping of equipment
elements connected thereto.
3 Switch off the vacuum cleaner by pressing the on/off
button (6) and unplug the appliance.
4 Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
5 Release the front cover fastening (11) and open the
cover.
6 Remove the SAFBAG dust bag module from the vacuum
cleaner chamber (14) .
7 Holding the bag plate deflect the lock, then the bag will
slip out automatically from the handle. Close the SAFBAG
bag cover in order to cover the opening of filled bag. Throw it
out into garbage container.
8
Put the plate of new dust bag towards (the window of)
handle in this way, that the plate will catch the fins, and the
ledge hit the window centrically. Snap the second end of plate.
The direction of bag installation is shown by the arrow on
the bag.
●
The SAFBAG bag module together with installed bag
(14) put into the vacuum cleaner container In this way,
that the ledge of SAFBAG bag module hit the slot on
the wall of container. Close the cover pressing it until
you hear the characteristic sound (“click”) – be careful to
avoid slam of the bag.
Do not vacuum without SAFBAG bag module
installed. The lack of SAFBAG bag module
disables to slam the upper cover of vacuum
cleaner.
ZELMER vacuum cleaners are equipped with SAFBAG dust
bags in the amount indicated in the table. It is recommended
to replace the dust bag if:
a) the red surface on bag loading indicator will appear,
b) the safety valve activates,
c) the vacuum cleaner operates poorly,
d) the dust bag is full.
The number of SAFBAG bags set that can be purchased,
is placed on a sticker located in the vacuum chamber.
End of operation cleaning
and maintenance
1 Switch off the vacuum cleaner by pressing the “on/off”
button (6) .
2
Unplug the appliance.
3 Wind the cord by pressing the cord rewind button (2) .
While doing this hold the cord to make sure it is not tangled
and the plug does not hit the vacuum cleaner housing.
4
Disconnect the telescopic tube from the nozzle or brush.
5 Disconnect the telescopic tube from the hose. In order to
remove the tube from the hose handle press the “A” locking
device and pull the tube in the direction of the arrow.
6
Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
7 The vacuum cleaner may be stored vertically or
horizontally. In order to do so, insert the fastening hook of the
combination brush to the combination brush fastener. The
hose may be attached to the vacuum cleaner, however you
have to make sure that it is not excessively bent during storing.
8
If necessary wipe the housing and the dust bag container
with a damp cloth (it may be soaked with dishwashing liquid)
and dry it or wipe until dry.
Do not use abrasive detergents or solvents.
Examples of problems while operating
the vacuum cleaner
PROBLEM ACTION
A characteristic “fluttering”
of the vacuum cleaner is
heard which indicates the
opening of the safety
valve.
• The dust bag may be full – replace
the dust bag.
• Replace the dust bag even if it is not
full yet. In unfavorable conditions, fine
dust might have clogged the pores on
the surface of the dust bag.
• The suction tube, the hose or the
attachment is blocked – remove the
cause of the clogging.
The dust bag is damaged. Remove the dust bag and the filters.
The suction power of the
vacuum cleaner is weak.
Replace the dust bag and the filters,
check the suction tube, the hose and
the nozzle - remove the cause of the
clogging.
The bag loading indicator
is operated.
Remove the end of suction hose
from the slot of front cover, and clean
the hose as well as the equipment
elements connected thereto.
The electrical installation
fuse went out.
Check if other appliances are not
plugged to the same electrical circuit
as the vacuum cleaner. If the fuse
goes out repeatedly, return the
vacuum cleaner to a service point.
F